Filter
Top Products
PROGRAMMING THE SYSTEM (INDIVIDUAL BUTTON PANEL):
1. Remove faceplate of GF entrance panel.
2. Lift rubber cap located on the upper right side of the GF-DA/B speaker module.
3. Using a long slender tool, momentarily press the programming button through the hole inside the GF-DA/B.
4. The In-Use LED will blink for approximately 15 seconds, then will become steadily lit.
5. With In-USE LED steadily lit, press the TALK button momentarily on the GFO-1DL you wish to program. (Only
one station can be programmed at a time.) Communication will be present (push-to-talk, release-to-listen at unit).
6. Momentarily press the call button in the GF-SW that is designated to call that tenant station. A single beep will be heard.
7. Press END button on GFO-1DL. (This is like hanging up the handset on a standard GF-1DK model.)
8. If the tenant has a second room station:
8a. Press the second unit's TALK button momentarily. Communication will be present.
8b. Press the same call button on the entrance panel. Two beeps will be heard.
8c. Press END button.
NOTE: If five beeps are heard when programming, that is an error indication. Clear the station by pressing and
holding the call button on the panel until a continuous beep is heard. Then reprogram by momentarily pressing the
call button again and releasing. A short single beep will be heard.
9. Repeat steps 5 through 8c to program each room station.
10. When programming is completed, press programming switch in GF-DA/B again. In-Use LED will turn off.
11. The system is now in regular operating mode.
12. Secure the rubber cap and replace the front panel.
13. Repeat the above programming process for each entrance panel in the system.
Pg. 3
Put Entrance panel in
program mode.
Press TALK button of
station to be programmed.
Press designated call button
in GF-SW momentarily.
Program each station in the
system in the same manner.
Press program button in
GF-DA/B again to return to
normal operation mode.
Press END
button on
GFO-1DL after
it has been
programmed.
PROGRAMMING DIGITAL ENTRANCE PANEL* TO CALL GFO-1DL ROOM STATIONS:
* NOTE: Program tenant's 3 or 4 digit number and name into the GF-NS/A first. Use computer program that comes with
the GF-NS/A or enter manually, as shown in the GF-NS/A instructions.
1~5. Follow steps 1 through 5 as described above.
6. Scroll to tenant's name or number (or enter number with keypad) on entrance panel, then momentarily press BELL
button (green-lit BELL symbol). A short beep will be heard.
7. Press END button on GFO-1DL. (This is like hanging up the handset on a standard GF-1DK model.)
7a. Program second room station the same way, and two beeps will be heard.
8. Continue programming each station in the system in this manner.
Refer to GF-NS/A Instructions for more detail on programming the digital scroll module.
PROGRAMMING THE CONCIERGE STATION (GF-MK) TO CALL GFO-1DL ROOM STATIONS:
1. Put GF-MK into programming mode as described in GF-MK Instructions, page 2-3.
2. Lift handset on GF-MK first.
3. At tenant station to be programmed, press TALK button. Communication will be established.
4. Scroll to tenant's name or number (or enter number with keypad), then momentarily press BELL button (green-lit BELL
symbol). A short beep will be heard.
5. Press END button on GFO-1DL. (This is like hanging up the handset on a standard GF-1DK model.)
5a. Program second room station the same way, and two beeps will be heard.
6. Continue programming each room station in the same manner, then go out of programming mode to return to normal
operation.
Refer to GF-MK Instructions for more detailed information on concierge programming.
PROGRAMMING & OPERATION: