Radio operations
RQT7125
26
Manual tuning
1 Press [TUNER BAND] (remote control: [TUNER/AUX])
to select “FM” or “AM”.
The unit comes on.
Every time you press the button:
FM →→ AM AUX
2 Press [PLAY MODE] on the remote control to select
“MANUAL”.
Every time you press the button:
MANUAL ↔ PRESET
3 Hold down [g/REW/
44
44
4] or [
33
33
3/FF/f] (remote
control: [(] or [)]) for a moment to search for a
station.
The frequency stops when it finds a clear station.
To stop during the process, press [g/REW/4] or [3/FF/f]
(remote control: [(] or [)]).
Under excessive interference, a station may not be found.
Press [g/REW/4] or [3/FF/f] (remote control: [(] or
[)]) repeatedly to tune step-by-step.
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display “MONO”.
Monaural sound is selected and noise reduces when reception is
weak.
Hold down [PLAY MODE] again to cancel the mode.
“MONO” is also canceled if the frequency is changed.
The radio
AM allocation setting
For the Middle East, South Africa and Southeast Asia
Main unit only
By adjusting the allocation, you can enable this tuner to receive AM
broadcasts allocated in 10 kHz steps.
Press [TUNER BAND] to select “FM”.
Press and hold [TUNER BAND]. After a few seconds, the display
will change to a flashing display of the current minimum frequency.
If you continue to hold the button down, the minimum AM frequency
will change. Release the button at this time.
To return to the original frequency indication, repeat above.
Note
After changing the “allocation” setting, the frequencies you previously
preset in the memory will be cleared.
Preset tuning
There are two methods of pre-setting stations.
Automatic presetting :All the stations the tuner can receive are
preset.
Manual presetting :You can select the stations to preset and
the order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER BAND] (remote control: [TUNER/AUX]) to select
“FM” or “AM”.
Automatic presetting
Remote control only
Do the following once each for FM and AM.
Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned in.
Manual presetting
Pre-set the stations one at a time.
1 Tune to the station (A left).
2 Press [PROGRAM].
3 While “PGM” is flashing
Press the numbered buttons to select a channel.
Alternatively, press [g/REW/4] or [3/FF/f] (remote control:
[g, 4] or [f, 3]) then press [PROGRAM].
The station occupying a channel is erased if another station is
preset in that channel.
Selecting channels
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [h10], then the two digits.
OR
1 Press [PLAY MODE] on the remote control to select
“PRESET”.
2 Press [g/REW/
44
44
4] or [
33
33
3/FF/f] (remote control:
[g,
44
44
4] or [f,
33
33
3]) to select the channel.
PROGRAM
TV/VIDEO
SETUP
DIMMER
CSM
DISC
REPEA
T
GUI DISP
ENTER
RETURN
SLOW/SEARCH
ZOOM
QUICK REPLA
Y
SOUND EQ
S.SOUND EQ
S.WOOFER
S.SRND
PL
CA
N
C
E
L
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
T
OP
M
E
N
U
P
.M
E
M
O
R
Y
D
V
D
/
C
D
P
L
A
Y
L
I
S
T
M
E
N
U
V
O
L
U
M
E
SHIFT
MANUAL
EQ
T
A
P
E
T
UN
E
R
/
A
U
X
TV
VOL
TV
VOL
TV
CH
TV
CH
PAGE
GROUP
D.RE-MASTER
SLEEP
AUT
O OFF
CLOC
K/
TIMER
PLAY/
REC
SKIP
TV
ECHO
MUTING
V.MUTE
AUDIO
C.F
CH SEL
S.POS
TEST
MIX 2CH
PLA
Y MODE
#
SUBTITLE
PROGRAM
PLAY MODE
TUNER/AUX
Numbered
buttons
SLOW/SEARCH
SKIP
TUNER
BAND
/REW/
/FF/
RQT7125(26-28)1 6/24/03, 10:46 AM26
