Filter
Top Products
,:'KEI:;'FUNcnoi\t.'::.. :.~
.'"'.":, :.,.,...~",.t-, '. " :.. . . '. '."',' . .
u
[MANU'J
['"TERl
LElETE ]
Co-J
\
~
I D~L J
[,w~L ]
This key turns on the Memory Scan and gives you "SCAN" on LCD, j: tile
squelch is in operation and Scan Memory Channels are programmed, Scan
starts its operation While it is on, the second digit of the channel nuf,'ber
shows movement indicating that the Scan is on.
When the radio receives a signal on a programmed channel while MC'11Orv
Scan is on, and squelch opens, it indicates its channel number and Sldy' ,0;
that channel. \X/hen the signal is gone, squelch closes and Memory Sc;m is
reaCtivated.
This key ;s used to check Memory Scan or when all the memory SCc1:1is
deleted. It is also used when "0" is flashing by mispressing the scan key
with no channel number programmed in memory scan. Ifyou pres:; this
key in a normal operation, it shows each channel number programmccJ in
Memory Scan.
This is the key to turn on the Memory Scan Channel. Select the char1nel
you wish to program, then press the ENTER Key.i'MEM" is indicated on
the left hand of the channel number to indicate that the program is com-
pleted.
This key deletes the programmed Memory Scan Channel(s). When this key
is pressed, the lowest numbered channel in the Memory Scan is indicated
and deleted. Ifyou keep pressing it. the next lowest channel numtJcr is
ir1dicated for deletion. "0" flashes whenall the memory scan channel:; are
deleted.
Thttse keys arc used (0 progr;:HT1cll<tnnel numbers. Tlw first numl)cr you
press becomes rile first digit, and if the second digit ,~ not progr.:wirned
within 10 seconds after the first one, it returns to lhe previous channel.
When the seleCted channel number does nOt exist, "E" flashes.
Bypressing this key, "DUAL" is indicated on the display. Every one and cihalf
seconds, it monitOrs CH 16, Ifthe receiver hearsa signal on CH ]6, it locks ontO
that channel. Wt,en the signal stops, it returns ro monitoring CH) 6 ('very
one and a half seconds. "DUAL" can be operated along with Memory Sc,m.
By pressing the "DUAL" key, it can be cancelled.
Bypressing this key, the power out-put can be changed to 1Wand ir WI!Ibe
indicated on LCD. Bypressing this key again, the power out-put returns (0
25W and the indication on LCD will be turned off.
r '-
lUS~NTJ
L~J
(87 AI
L_J
This key gives you international cllannels or USAchannels with an indica-
tion of "INT" or "USA" on the display. When the radio is activated,
international channels are auromarieally available and by pressing the key,
it goes ro USA channels
This key gives you instant access to channel 16 and "'J6" will be indicated
on LCDwhen you press it.
This key gives you instant access to channe/87A and "87"will be indicated on
LCD when you press it. If channel 87A is seleCted from keyboard while op-
erating USA. channels, LCD WILL FLASH" u",
I.
NOTE:
The MC790 has a self-check function to indicate malfunCtions due to overly high
incoming nj;)jseleve/sand sudden, drastic changes of power voltage levels wllen the
unit is on. This self-check will illuminate all segments of the LCDwhen triggered. If
tllis should occur, t?urnunit off, then back on to rese[ rhe microprocessor chip. The
programmed functions will not be erased as long as the Back-up BaneI)', is functioning.
Plea'se read the Owner's Manual carefully before operating your unit.