Filter
Top Products
English - 27
equipment, operations or procedures that could
aect the operation of the equipment. If this hap-
pens the telephone company will provide advance
notice in order for you to make necessary modi-
cations to maintain uninterrupted service.
Please follow instructions for repairing, if any
(e.g. battery replacement section); otherwise do
not substitute or repair any parts of the device
except as specied in this manual. Connection to
party line service is subject to state taris. Con-
tact the state public utility commission, public
service commission or corporation commission
for information. is equipment is hearing aid
compatible.
If you experience trouble with this equipment,
contact the manufacturer (see the cover of this
manual for contact information) or an authorized
agent. If the equipment is causing harm to the
telephone network, the telephone company may
request that you disconnect the equipment until
the problem is resolved.
If your home has wired alarm equipment con-
nected to a phone line, be sure that installing the
system does not disable your alarm equipment. If
you have questions about what will disable alarm
equipment, contact your telephone company or a
qualied installer.
Any changes or modications to this product not
expressly approved by the manufacturer or other
party responsible for compliance could void your
authority to operate this product.
NOTICE: According to telephone company
reports, AC electrical surges, typically resulting
from lightning strikes, are very destructive to
telephone equipment connected to AC power
sources. To minimize damage from these types of
surges, a surge arrestor is recommended.
FCC Part 15 Information
is device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) is device may not cause harmful
interference, and (2) is device must accept
any interference received, including interference
that may cause undesired operation. Privacy of
communications may not be ensured when using
this phone.
FCC PART 15.105(b): Note: is equipment has
been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15
of the FCC Rules. ese limits are designed to
provide reasonable protection against harmful
interference in a residential installation. is
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment o and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment
and receiver.
x Connect the equipment into an outlet on a
circuit dierent from that to which the receiver
is connected.
x Consult the dealer or an experienced radio/TV
technician for help.
FCC RF Exposure Information
is product complies with FCC radiation expo-
sure limits under the following conditions:
x e base must be placed to allow a minimum of 20
cm (8 inches) between the antenna and all persons
during normal operation.
x e base must not be collocated or operated in
conjunction with any other antenna or transmit-
ter.
x e handset is designed for body-worn operation
and meets FCC RF exposure guidelines when
used with any belt clip, carrying case, or other
accessory supplied with this product. (All neces-
sary accessories are included in the package; any
additional or optional accessories are not required
for compliance with the guidelines.) ird party
accessories (unless approved by the manufacturer)
should be avoided as these might not comply with
FCC RF exposure guidelines.
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE: is equipment meets the applicable
Industry Canada Terminal Equipment Technical
Specications. is is conrmed by the registra-
tion number. e abbreviation IC before the
registration number signies that registration was
performed based on a Declaration of Conformity
indicating that Industry Canada technical speci-
cations were met. It does not imply that Industry
Canada approved the equipment.
NOTICE: e Ringer Equivalence Number
(REN) for this terminal equipment is marked on
the equipment itself. e REN assigned to each
terminal equipment provides an indication of
the maximum number of terminals allowed to be
connected to a telephone interface. e termina-
tion on an interface may consist of any combina-
tion of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
Radio equipment
e term IC before the radio certication number
only signies that Industry Canada technical
specications were met. Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference
that may cause undesired operation of the device.
"Privacy of communications may not be ensured
when using this telephone".