Filter
Top Products
2
USER GUIDE
Figure 4.
ezEarhook connected
for right and left ears
Figure 2.
ezTalker with ezFit Ring
Figure 3.
ezTalker with Comfort Pad
To Cancel Pairing Mode
While you are in pairing mode, you can cancel the pairing process and
turn off the headset.
1. While in pairing mode, press and hold the TALK button approximately
three seconds until both LEDs turn off or you hear the OFF tone.
Fitting EZTALKER On Your Ear
EzTalker is designed to fit comfortably in your ear. For added comfort, you
can add the optional ezEarhook , ezFit Ring, and/or comfort foam pad. For
additional comfort, you can add the comfort foam pad that is included
with ezTalker.
To Place the Headset On Your Ear
1. Place the ezTalker speaker in your ear with the microphone angled
toward your mouth as shown. The headset should fit snugly in your
ear and remain in your ear when you move your head. However, if
the speaker is too small for your ear, you can add the ezFit Ring that
is provided with your headset.
To Add the ezFit Ring
1. Stretch the ezFit Ring around the end of
the microphone as shown.
To Add the Comfort Pad
1. Stretch the comfort pad around the end of the
microphone as shown. The comfort pad can be placed
over the ezFit Ring, if both are needed.
To Add the ezEarhook
1. Right ear: From the rear of ezTalker, insert
the bottom of the ezEarhook into the small
hole on the left side of the headset,
pushing until it stops.
Left ear: From the rear of ezTalker,
insert the bottom of the ezEarhook into
the small hole on the right side of the
headset, pushing until it stops.
2. You can mold the soft plastic on ezEarhook
to better fit your ear, and/or adjust the
placement of the ezEarhook stem through
the headset (further in/out).
To Remove the ezEarhook
1. Gently pull the ezEarhook away from the headset until it separates
from the headset.
Powering ezTalker
To Turn On the Headset
Press and hold the TALK button approximately four seconds until the
blue LED flashes or until you hear the ON tone.
The headset turns on
and is placed in standby mode, ready to make and receive calls. While
the headset is on and in standby mode, the blue LED will flash at two-
second intervals.
To Turn Off the Headset
When the headset is on, press and hold the TALK button approximately
four seconds until the blue LED turns off or until you hear the OFF tone.
The headset turns off.
Making Calls
You can make calls from your mobile phone, or directly from ezTalker
using voice dialing commands (if this feature is supported by your
mobile phone).
To Make Calls From Your Mobile Phone
1. Dial the call from your mobile phone.
The call is automatically
connected to your headset.
To Make Calls Using Voice Dialing (if supported by your mobile phone)
1. Press the TALK button on your headset.
2. When prompted by the mobile phone (usually about five seconds),
speak the name of the person you wish to call.
The call is
automatically connected to your headset.
TIP
: In a noisy environment, you should dial the number from the mobile
phone keypad as the loud background noise may interfere with
voice commands.
Receiving Calls
When you receive a call on your mobile phone, you will hear the mobile
phone ring before you hear the ring tone through your headset as there
is a small delay before the headset recognizes the incoming call.
1. When you hear ring tone on your headset, press the headset TALK
button.
The call is automatically connected to your headset.
NOTE:
For some mobile phones, you must configure the phone to
answer calls directly on your Bluetooth headset. Refer to the mobile
phone user guide for instructions for initiating this feature.
Ending Calls
1. When you have finished your call, press the headset TALK button.
The call will be disconnected.