Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Customer Assistance WarrantyIntroduction Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Mode Functions
Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
DCS Privacy Code
LI 7300
Mode Button
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Privacy Codes
•
Your microTALK
®
radio incorporates two (2) advanced coded squelch
systems that can help to reduce interference from other users on any
given channel. CTCSS (Continuous Tone Coded Squelch System) provides
38 privacy codes and DCS (Digitally Coded Squelch) provides 104 privacy
codes. This provides a total of 142 Privacy Codes. Either system can
be used on all channels, but both systems cannot be used on the same
channel at the same time.
To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will remember the last
privacy code system and number you select.
The privacy code 00 is not a privacy code, but allows all signals
to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.
Set CTCSS Privacy Codes
•
To select a CTCSS privacy code:
1. After selecting a channel, press the
Mode button until the CTCSS icon appears and
the small numbers flash on the display (01
through 38).
If DCS is turned on at the channel selected,
the display will flash the
CTCSS icon and “OFF.” To switch from
DCS to CTCSS, press the Channel Up
or Channel Down button while the display
is flashing “OFF.” The display
will then show the small numbers flashing
and you will then be able
to proceed to step 2.
2. Press using the Channel Up or Channel
Down button to select a CTCSS privacy
code. You can hold the Channel Up or Channel
Down button for fast advance.
CTCSS Privacy Code
LI 7300
Mode Button
LI 7300
Channel Button
LI 7300
Channel Button
10
English
11
Nothing Comes Close to a Cobra
®
3. When your desired CTCSS privacy code is
displayed, choose one of the following:
a. Press the Mode button to enter the new setting
and proceed to other functions.
b. Press the Lock/Enter button to enter the new
setting and return to Standby mode.
c. Do not press any buttons for 15 seconds
to enter the new setting and return to Standby
mode.
Set DCS Privacy Codes
•
To select a DCS privacy code:
1. After selecting a channel, press the Mode
button until the DCS icon appears and the small
numbers flash on the display (01 through 104).
If CTCSS is turned on at the channel
selected, the display will flash the
DCS icon and “OFF.” To switch from
CTCSS to DCS, press the Channel Up
or Channel Down button while the
display is flashing “OFF.” The display
will then show the small numbers
flashing and you will then be able
to proceed to step 2.
2. Press the Channel Up or Channel Down button
to select a DCS privacy code. You can hold the
Channel Up or Channel Down button for fast
advance.
3. When your desired DCS privacy code is displayed,
choose one of the following:
a. Press the Mode button to enter the new setting
and proceed to other functions.
b. Press the Lock/Enter button to enter the
new setting and return to Standby mode.
c. Do not press any buttons for 15 seconds
to enter the new setting and return to Standby
mode.
CXR925C_ENG_MANL.indd 10-11 12/15/09 2:19 PM