Filter
Top Products
continued
Handset Receiver Volume Control
(located on the left side of the
handset)
1
To increase the sound level, press
the
a
key.
2
To decrease the sound level, press
the
@I
key.
If you subscribe to special local
telephone company services like
Call Waiting or Call Forwarding,
you can access them by pressing
[=I
whenever you would press
the switchhook on a regular phone.
To
redial the last number dialed from
the handset:
1
Press
[PHaNEl.
2'
Wait for the PHONE indicator to
go on and for a dial tone.
3
Press
m.
The last number you called is stored
in the redial memory until you dial
i
another number.
9
.
-
NU0
Mute allows you to hew your caller
but prevents the caller from hearing
you.
1
Press
m.
2
The MUTELOW BATT indicator
will light to indicate the Mute
feature is activated.
3
To continue your conversation,
press
lMUrEl
again.
Press
b@@
on the handset during
incoming ringing to disable the
ringer for the duration of the call.
The Hold feature allows you to keep
a call on the line while you step
away from the phone or while you or
someone else takes the call on an
extension phone.
1
Press
lHOLD].
2
The PHONE indicator will blink
slowly to indicate the call is on
hold.
3
To release Hold, press
@@
again.
IMPORTANT.-
If you are using the
Hold feature to switch to another
extension, you must first place the
call on Hold. After the extension
phone has been picked up, release
the Hold feature and press
[OFF]
on
the
91
1
1 to resume your conversation
on the extension phone.
AthranadHoSelea-
The Cordless Telephone
9
1
1
1 's
advanced Autoselect feature will
automatically select the clearest
channel, even during a conversation.
During automatic channel change
your conversation may be interrupted
for about
1
second while the unit
scans and selects a new channel.
If you have dial pulse (rotary)
service, this feature allows you
to enter codes or tones needed to
operate answering machines, or use
electronic banking services, calling
cards, and other special services.
This feature will operate most special
services; however, some services
may actually require a touch tone
line. To be sure, ask the company
that provides the special service.
NOTE:
If you have touch tone
service, you do not need to use the
Temporary Tone feature.
To use temporary tone dialing:
Dial the call n&rnally.
Press
I+TONE].
Enter numbers or symbols
required.
End the call normally (Temporary
Tone is automatically shut off).
The handset ringer is capable of four
different types of ringing tones. The
following sections detail how to
change the different tones and to
turn off the ringer on the handset.
To program, the handset must be
[OFFI.
To select a different ringer type do
the following:
1
Press
m.
2
Press
O.
3
Press a key
(@-0)
to select a
ringer type.
4
Press
m.
To turn off the ringer on the handset,
do the following:
1
Press
m.
2
Press
@l.
3
Press
i3-J
to turn off the ringer.
4
Press
m.
To turn ringer on again, see
"Programming the Ringer Type."
To check the ringer which is currently
programmed, do the following:
1
Press
(PROG].
2
Press
O.
3
Press
Q
again to check the ringer.
4
Press
m).
This feature is useful if you misplace
the handset.
To locate the handset using the
Handset Locator feature:
1
Press
(PAGEIHANOSET
LOCATOR].
2
A
repeating paging tone is
sounded at the handset for
approximately
30
seconds.
To cancel the Handset Locator
feature:
Press
[OFFI
on the handset or press
[PAG~ANDSET
LOCATOR]
on the base.