7
Press the MENU button and select Sound using the
e
or
d
buttons, press the
8
button to enter.
Select and adjust to obtain the best sound settings for your
environment using the
e
,
d
and
7 8
buttons.
Press the MENU to return to Main Menu. These settings
automatically store when you exit the menu.Press the MENU button
to exit menu.
■ OSD Language
Use the 7 or 8 buttons to select the prefered OSD language
(French, German, Italian, Spanish, Dutch). Press the MENU but-
ton to exit
■ AV2 setting
In setting menu, to select AV2 press the d button and set to Y,Pb,Pr
or RGB, H/V depending on your external equipment.
1. Press the MENU button. Select Setting using the e or d button
press the 8 button to enter.
2. Select AV2 setting using the e or d button.
3. Press the 7 or 8 button to select either Y,Pb,Pr or RGB H/V.
4. Press the MENU button to exit, this automatically stores your
changes.
5. Press the MENU button to exit.
■ Off-timer setting
The Off timer will switch the monitor into the standby mode when the
selected time has elapsed.
1. Press the MENU button. Select Setting using the e or d button
press the 8 button to enter.
2. Select Timer using the e or d button, press 8 buttons to enter.
3. Press the 7 or 8 button to change time.
The time changes in 5 minute steps.The maximum time is 120 min-
utes.
If you have set the off timer, a display appears in the corner of the
screen when the recall button is pressed.
✐ If the monitor is switched off by the standby button
4
on the
remote control or by the standby switch
4
on the bottom of the
LCD monitor the timer settings will be cancelled.
Connect your PC to either PC-IN or RGBHV on the rear of the set.
Once connected select PC mode or AV2 (RGBHV, see page 4 for
AV2 input settings) via the v button on your remote control. The
set will become a monitor for the PC.
By pressing the MENU button on the remote control a menu window
will appear on screen, this allows the settings to be adjusted.
To adjust the Picture settings select picture using the e or d buttons
on the remote then the 8 button to enter the following picture
settings menu.
Press the 7 or 8 buttons to adjusted the Picture brightness and the
same to adjust the contrast of the picture. Press the 8 button to
enter sub menus
Picture position changes the picture horizontally or vertically, this is
done by using the 7 or 8 buttons on the remote control.
Video adjust changes the Phase and the clock of the screen. If the
picture is blurred or grainy this function will adjust it to a clearer
picture by using the 7 or 8 buttons on the remote control.
Auto Adjust will automatically adjust the picture by using the 8
button. This will change all the above settings automatically .Auto
adjust can also be achieved by pressing the /recall
button on the remote control without having to select the menu
Resolution displays the current resolution of the picture. This is for
information only and cannot be adjusted.
White tone: Using the 7 or 8 buttons it is possible to adjust the
colour tone of the picture using the White tone Red(R) / Green (G)/
Blue(B). This will adjust the picture to show more or less of the
chosen colour. For example if red is selected you can adjust the pro
portion of red in the picture to increase or decrease using the 7 or 8
buttons
Native Resolution is used when the PC can output WXGA
1366 x 768. The setting on your Monitor set can be changed
to receive XGA/WXGA signal using the 7 or 8 buttons . Once the
native resolution has been selected, save the settings by switching
the monitor off then on using the standby button.
For Sound settings refere to previous menu
Setting: select the menu button on your remote and using the e or
d buttons to select Settings. The 8 button will enter the settings
menu.
Timer and AV2 settings are the same as in all other input modes
(pg 7)
Power save if turned ON will switch the monitor into Powersave
mode after 1 minute if no signal is detected, the LED light will turn a
brighter blue to indicate stand by. The monitor will automatically turn
back on when a signal has been detected (PC input / RGBHV).
Use 7 or 8 buttons to select power save ON or OFF.