Filter
Top Products
GETTING STARTED
WALL MOUNTING
5. CHARGE THE HANDSET BATTERIES
BEFORE USE. The batteries recharge
automatically whenever the handset is
in the base unit cradle. The batteries
must be charged for 16 hours before
using your phone for the first time.
6. CHECK FOR A DIAL TONE. After the
batteries are charged, pick up the
handset and press the PHONE key. The
IN USE indicator should light up, and
you should hear a dial tone. If not, see
IN CASE OF DIFFICULTY.
CAUTION:
1. Never install telephone wiring during a
lightning storm.
2. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
3. Never touch uninsulated telephone wires
or terminals unless the telephone line
has been disconnected at the network
interface.
4. Use caution when installing or modifying
telephone lines.
1.Choose a spot near an electrical outlet
and a telephone jack.Your phone
requires a modular telephone jack and
a standard electrical outlet (120V AC).
The power cord is six feet long; make
sure there is an electrical outlet within
reach of the base. The outlet should not
be controlled by a wall switch. If the
switch is ever turned off, the phone will
not operate.
2.Mount the base on the wall. Position
the base so the mounting studs will fit
into the holes at the back of the base.
Position the power cord to extend down
the wall the phone is to be mounted on.
Slide the base down on the mounting
studs until it locks into place.
3.Connect the telephone cord. The
telephone line cord has a snap-in plug
at each end. Insert one of the plugs into
the jack on the bottom of the base. Insert
the other end of the plug into the wall
jack.
MEM/PROG, Number Button (0-9).
RINGER SWITCH
* To turn the ringer switch ON for
incomming call alert.
* To turn off ringer move switch to OFF
position.
REDIAL/PAUSE KEY
* When you hear the dial tone, pressing
the REDIAL/PAUSE key will dial out the
last number that was called on your
phone.
TONE/ KEY
* In PULSE dialing mode, this key is used
to switch to Temporary TONE dialing
mode.
VOLUME KEY
* There are four volume setting. Press the
VOL key repeatedly to cycle from lowest
to highest earpiece volume.
BATTERY LOW WARNING BEEP
* Upon pressing PHONE, the Handset will
beep to indicate that the battery pack
needs to be recharged.
PHONE LED
* The PHONE LED lights when the phone
line is being used by the handset.
* It flashes with an incoming ring.
* It flashes during PROG mode.
PHONE KEY/ FLASH KEY
* Press the PHONE key to make a call.
* If you are currently on a call, pressing
PHONE flashes the line. This would be
used with a feature like call waiting to
answer your second call.
CHAN KEY
* Pressing the CHAN key when the
handset is in use will activate a channel
change to the next free channel.
* This is used if you are experiencing
noise or interference on the current
channel.
OFF KEY
* Press the OFF key to exit all modes of
operation.
MEM/PROG KEY
* Press the MEM/PROG key to enter
MEMORY mode.
* The sequence for dialing out a speed
dial number in memory is: PHONE,
4.Connect the power cord. Plug the DC
connector into the DC jack at the rear of
the base unit. Plug the AC power
adapter into an electrical outlet.
4
5
7
BASE UNIT FEATURES
REPLACEMENT BATTERY ORDER FORM
For VTECH 9109 Cordless Telephone
Name: Address:
City: State: Zip:
daytime phone Number: ( )
ORDER INFORMATION
For Model VT 9109
(QTY.) Batteries @$14.95 each............................$
$5.95 Shipping & Handling Per Battery Ordered....................................................$
METHOD OF PAYMENT: DO NOT SEND CASH
CHECK MONEY ORDER VISA MASTERCARD AMERICAN EXPRESS
CREDIT CARD# EXP. DATE
CARD HOLDERÕS SIGNATURE
PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SEND TO:
VTECH COMMUNICATIONS
8770 SW NIMBUS AVENUE
BEAVERTON, OREGON 97008-7195 USA
YOU MAY ALSO ORDER BY PHONE. CALL 1-800-595-9511
CUT
6
CUT
HANDSET FEATURES
Setting Up Your
VT 9109
1. Choose an area near an electrical outlet
and a telephone wall jack.
2. Connect the telephone line cord. Insert
one end of the telephone line cord into
the jack at the rear of the base unit. Plug
the other end into a telephone wall jack.
Make sure the plugs snap securely into
place.
3. Plug the AC power adapter into an
electrical outlet and the DC connector to
the back of the base unit.
CAUTION:Use only the AC adapter
shipped with your
VT 9109
. This
is a Class 2 AC adapter,
specifically designed for use
with the
VT 9109
.
NOTE: Connect power to the base unit
before placing the handset in the
cradle.
4. To select TONE dialing press, MEM/
PROG, , ,MEM/PROG, To select PULSE
dialing press, MEM/PROG, , ,MEM/
PROG.
NOTE: Your
VT9109
is preset for TONE
dialing.
*
*
*
#
PAGE KEY
* Press the PAGE key to page the
handset.
* Press it a second time to cancel a
page.
* The base will ring the handset 120
seconds before ending the page
automatically.
* PAGE can be cancelled by pressing
PHONE key following by OFF key.
IN USE/CHARGE LED
* The IN USE/CHARGE LED
illuminates steadily when the
handset is in the base cradle to
indicate that the handset battery is
being charged or the handset is off-
hook.
VOLUME KEY
PHONE LED
PHONE/FLASH KEY
OFF KEY
CHAN KEY
TONE/* KEY
MEM/PROG KEY
REDIAL/PAUSE KEY
wallboard
wooden
stud
TELEPHONE
WALL JACK
AC ELECTRICAL
OUTLET
RINGER SWITCH