Filter
Top Products
Parts Check List:
1. Handset
2. Base Unit
3. Telephone line cord
4. Battery
5. Power Adapter
6. User’s Manual
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire,electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink
or swimming pool).
5. Do not place this product on an unstable surface, such as a table, shelf or
stand. The product may fall, causing serious damage.
6. Slots and openings in the back or bottom of the base unit and handset are
provided for ventilation. To protect them from overheating, these openings
must not be blocked by placing the product on a soft surface such as a bed,
sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation
is not provided.
7. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply in your
home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product
where the cord may have anyone walking on it.
9. Never push objects of any kind into this product through slots in the base or
handset as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any kind on the
product.
10. To reduce the risk of electric shock, do not disassemble this product, but take
it to an authorized service facility. Opening or removing parts of the base or
handset other than specified access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause electric shock when
the product is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the risk of
fire or electric shock.
12. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as improper adjustment of other controls may result in
damage and often requires extensive work by an authorized technician
to restore the product to normal operation.
E. If the product has been dropped and the base and/or handset has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There
is a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal talk
mode.
SAVE THESE INSTRUCTIONS
1. Slide the battery cover off by gently
pressing on the recessed area with
a downward motion.
2. Unplug and remove the old battery.
3. With the red and black wires at the
bottom of the battery, angle the top
of the battery into the compartment,
under the claws. Next, press the
lower end of the battery down, so it
is held in place by the lower claw.
Now, plug the connector into the
socket, located below the battery.
Slip the battery wires into the guide,
located below and to the left of the
socket.
4. Replace the battery cover by sliding
it into place.
5. The new battery must be charged
before using your telephone. Place
the handset in the base unit to allow
it to charge for 15 hours. Maximum
Introduction
To purchase replacement batteries,
call VTech Communications at 1-800-
595-9511. In Canada, call VTech
Telecommunications Canada Ltd. at
1-800-267-7377.
Important Safety Instructions
Installing/Replacing the Battery
battery life between charges is approximately 3.75 hours of talk time or
3.75 days of standby.
CAUTION: To reduce the risk of fire or injury, read and follow these
instructions:
1. Use only the VTech battery supplied, or equivalent.
2. Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause damage to the eyes or skin. It may be toxic if swallowed.
3. Exercise care in handling battery in order not to short the battery with
conducting materials such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
4. Do not dispose of the battery in a fire. The cell may explode.
1
2
3
Setting Up Your 2151
1. Choose an area near an electrical outlet and a telephone wall jack.
2. Plug the AC power adapter into an electrical outlet and the DC connector
to the power jack on the bottom of the base unit. Insert the cord in the
channel guide.
CAUTION: Use only the AC adapter shipped with your 2151. It is
specifically designed for this product.
NOTE: Connect power to the base unit before placing the handset in
the cradle.
3. CHARGE THE HANDSET BATTERY BEFORE USE. The battery
recharges automatically whenever the handset is in the base unit. The
battery must be charged for 15 hours before using your phone for the
first time.
4. Connect the telephone line cord. Insert one end of the telephone line
cord into the phone jack on the bottom of the base unit. Plug the other
end into a telephone wall jack. Make sure the plugs snap securely into
place. Insert the cord in the channel guide.
5. CHECK FOR A DIAL TONE. After the battery is charged, pick up the
handset and press the ON key. You should hear a dial tone. If not, see
IN CASE OF DIFFICULTY.
ON/ FLASH KEY
• Press the /PHONE key to
make a call.
• If you are currently on a call, and
hear a call waiting tone, press
FLASH to switch to the second
call. Press FLASH again to return
to the original call.
VOLUME CONTROL
• While on a call, press the or
keys to adjust the listening
volume. The handset will emit a
double beep when the maximum
or minimum volume level has been
reached.
VOLUME/CID/PHONEBOOK
KEY
• When phone is not in use, press
( ) to display Caller ID
information.
• When phone is not in use, press
( ) to display directory entries.
OFF KEY
• Press the OFF key to end a call
or exit all modes of operation.
Getting Started Handset Features
REDIAL / PAUSE KEY
• You can store pauses into your
speed dial numbers. See Storing
Pauses in Memory for details.
CHAN/DELETE KEY
• Pressing the CHAN key when
the handset is in use will activate
a channel change to the next
free channel. This is used if you
are experiencing noise or
interference on the current
channel.
• When viewing the call log, press
to delete the current record
displayed.
• While handset in idle mode,
press and hold to delete all
records in the call log.
PROG/SELECT KEY
• Press PROG.
•
Press SELECT to store a
directory entry.
TONE/ * KEY
• In PULSE dialing mode, this key
is used to switch to temporary
TONE dialing mode.
PAGE
Press to page the handset for up
to 60 seconds. Press again, or
press OFF on handset, or place
handset in base to cancel the
page.
4
5