Filter
Top Products
Phone Connection
1. Connect the telephone at the RJ11 socket (PHONE) provided at the rear side of the unit.
2. Lift the handset and hear for the dial tone.
VISIONTEK GSM Fixed Cellular Terminal 81GF (FCT) with G3 Fax connectivity is a single line
PSTN simulation made available from GSM /GPRS network. This gadget performs the task of
converting GSM calls to normal analog telephone line with an output similar to existing
PSTN environment with all the basic features and additional G3 Fax feature. It provides
access to home, office, or any remote location where phone and fax service is needed and
GSM footprint is available. Primary telephone fax service, extra lines and security backup are
made available thus facilitating outgoing voice and fax calls anytime and anywhere.
VISIONTEK FCT package consists of the following:
nGSM FCT – 1 No.
nAntenna – 1 No.
nLine Cord – 2 No.
nPower Adaptor – 1 No.
nRS-232 Serial cable.
nUser Manual – 1 No.
1
Introduction
3
Operation
1 2 3
SIM Card Installation:
The FCT requires a SIM (Subscriber Identification Module) for its normal operation. SIM
socket is provided on the bottom side of the unit.
1. Disconnect power supply if it is already connected to the power socket.
2. Remove the SIM card window by removing the screw.
3. Open the SIM card holder.
4. Ensure for proper direction of the SIM card and insert it gently into the SIM card holder.
5. Close the SIM card holder and press the SIM card holder in forward direction for locking.
6. Fix the SIM card window with the screw.
Antenna Installation:
1. Antenna connector is provided at the rear side of the unit.
2. Connect the antenna supplied with the unit to the connector and ensure for proper
contact.
Power Connection:
1. Plug in the primary of adaptor into 230V AC power socket and the secondary to the
Power socket (DC 14.2/3A) provided at the rear side of the unit.
2. Connect the battery cable of the Unit to the external battery (12V/5AH). Battery socket
is provided at the rear side of the unit. Ensure for proper polarity.
3. Switch ON the unit and observe for the following LED indications on the front panel.
- Red LED indicates the presence of AC power.
- Green LED indicates the presence of Network. LED Blinking indicates the availability of
network.
Receiving Calls
1. The telephone will give a ring on receiving the incoming call.
2. Receiver number is displayed on the LCD display **.
3. Pick up the handset to answer the call.
** Subject to network support
2
Installation
Making Calls
1. Lift the handset and hear for the dial tone.
2. Dial the phone number. The dialed number is displayed on the LCD display.
3. After finishing dialing, Press # key on the telephone instrument to send the dialed
number. This will avoid the wait time of 7 seconds. Call progressive tone will be heard in
receiver till call gets connected.
SENDING FAX MESSAGES:
1. Insert the document into the document feeder.
2. Pick up the handset or press the hands free key on the fax machine.
3. Dial the number of the receiving machine.
4. Wait for the connection. Depending on the setting of the receiving machine, a facsimile
reception tone will be heard.
5. Once the fax machine is connected, the fax machine will automatically transmit the
document.
FAX CONNECTION:
1. Connect the fax at the RJ11 socket (FAX) provided at the rear side of the unit.
2. Lift the fax handset and hear for the dial tone.
NOTE: (1) The fax communications service has to be activated by the network
operator. Otherwise the network will not allow faxes to be sent or received.
(2) You will not be able to make or receive the other voice calls while a fax
communications is established.
1. The FCT is programmed to automatically detect the out going calls made by FAX
machine. This means the user simply has to use the fax in a same way as a conventional
telephone line
2. Incoming faxes are received in the same way as using the fixed line.
SENDING AND RECEIVING FAX MESSAGES:
The VISIONTEK 81GF FCT terminal allows the connection of group3 fax in the similar way as
telephone instrument.
RECEIVING FAX MESSAGES:
1. The fax machine will automatically answer the incoming calls.
2. If the fax machine detects fax tones, it begins to receive faxes automatically.
NOTE: (1) For additional information, kindly refer to the user guide of the fax machine.
(2) Use * key to scroll the menus, # to confirm and go On-hook to skip the
programming,
Step-1: On successful entry of password, LCD shows “CHANGE PASSWORD”. Press # key to
change the default password or Press * for next menu.
Step-2: Display shows “ERASE MEMORY”. Press # key to erase the memory. Press key for
next menu.
Step-3: Display shows “LOCAL NUM YES”. Press # key to enter the area code to avoid dialing
the area code for local calls. Press * key for next menu.
Step-4: Display shows “LOCAL NUMBER REVIEW”.
Press # key to review the area code entered. Press * key for next menu.
1. In normal mode, the LCD display shows VISIONTEK. On lifting the handset, display shows
“PLEASE DIAL”.
2. Press ** and enter the password. Default password is 9999.
Programming Mode 1