Filter
Top Products
1) Located on the front of the telephone, above the speaker grill, is
the wall/desk mount clip. Remove this clip by pushing upward.
2) Rotate clip one half turn (180 degrees) so the side with the pro-
truding edge is towards the top. This edge will hold the handset.
3) Slide the clip downward into the slot until it snaps into place.
4) Turn the telephone over onto a non-abrasive surface so the back
side is up, facing you.
5) Locate the mounting bracket, and firmly push back and pull up
to remove.
NOTE: There are four (4) retaining tabs.
6) Rotate the mounting bracket one half turn (180 degrees) so that
the mounting eyelet is facing in the same direction as the mounting
eyelet located on the bottom surface of the telephone.
7) Insert the top two retaining tabs of the mounting brackets into
the mounting bracket slots located near the middle of the telephone,
then firmly push down and insert the retaining tabs on the
opposite side.
8) Connect a short modular line cord into the jack on the back of
the phone (labeled TO TEL). Route the line cord through the line
cord channel. Connect the other end of line cord to the phone
jack on the wall mounting plate.
9) Turn the telephone over, and slide the telephone onto the mount
ing posts on the wall plate in a downward direction. Both eyelets
should line up with the mounting posts. When properly installed,
the telephone will be stable and secure.
10) Complete wall mounting by installing the handset and handset cord.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal Communications Commission,
under Part 68 rules and regulations for direct connection to the telephone lines. In order to comply
with these FCC rules, the following instructions must be carefully read and applicable portions fol-
lowed completely:
1) Direct connection to the telephone lines may be made only through the standard modular cord
furnished, to the utility installed jack. No connection may be made to party or coin phone lines.
On the bottom of the phone is a label that contains, among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If requested this information
must be provided to the telephone company. The USOC Jack for this equipment is RJ11C.
2) The telephone company, under certain circumstances, may temporarily discontinue and make
changes in facilities and services which may affect the operation of the users' equipment. However,
the user shall be given adequate notice in writing to allow the user to maintain uninterrupted service.
3) In certain circumstances, it may be necessary for the telephone company to request information
from you concerning the equipment which you have connected to your telephone line. Upon request
of the telephone company, provide the FCC registration number and the ringer equivalence number
of the equipment which is connected to your line; this information will be found on the device.
4) If any of your telephone equipment is not operating properly, you should immediately remove it
from the telephone line. It may cause harm to the telephone network.
5) If the telephone company notes a problem, they may temporarily discontinue service. When practical,
they will notify you in advance of disconnection. If advance notice is not feasible, the telephone com-
pany must; promptly notify you of such temporary discontinuance; afford the opportunity to correct
the condition; inform you of your rights to bring a complaint to the FCC under their rules.
6) Repairs to the device may be made only by the manufacturer or an authorized service agency.
This applies at any time during and after warranty. If unauthorized repair is performed, registration,
connection to the telephone lines and remainder of warranty period all become null and void.
7) This equipment is hearing aid compatible.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communications. However, there is not a guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
a) move the telephone away from the receiver. b) consult the dealer or an experienced radio/TV
technician for help. Any changes made by the user not approved by the manufacturer can void the
user's authorty to operate the telephone.
INDUSTRY OF CANADA REQUIREMENTS
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective operational and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The
department does not guarantee the equipment will operate to the users satisfaction. Before installing
this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above conditions may not pre-
vent degradation of service in some situations. Repairs to certified equipment should be coordinated
by a representative designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause to request
the user to disconnect the equipment. Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines, and internal metallic water pipe systems, if
present, are connected together. This precaustion may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority or electrician, as appropriate.
The Load Number of this device is 44.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indi-
cation of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. This
telephone connects to the telephone network under the connecting arrangement code CA11A.
TELEDEX DIAMOND+L2S DIAGRAM
RING VOLUME
Adjusts the ringer volume
to Low or High setting.
DATA PORT
LINE 1 KEY
LINE 2 KEY
HOLD KEY
HANDSET VOLUME KEY
Changes handset volume by
pressing repeatedly.
MUTE KEY
Deactivates handset/speakerphone
microphone for privacy during calls.
SPEAKERPHONE KEY
Activates speakerphone. When LED is
illuminated, speakerphone is active.
REDIAL KEY
To automatically redial
last number dialed
AUTO DIAL KEYS 6-11
For easy, one-touch dialing of guest services or
PBX features. Programmed during installation.
AUTO DIAL KEYS 1-5
For easy, one-touch dialing of guest services or
PBX features. Programmed during installation.
MESSAGE WAITING LIGHT
Signals that a message is waiting for retrieval.
See your system administrator for instructions
on retrieving messages.
PAUSE KEY (hidden)
For programming of PAUSE duration.
See instructions for programming details.
FLASH PROGRAMMING KEY (hidden)
For programming of FLASH duration.
See instructions for programming details.
STORE KEY (hidden)
Used in programming of number sequences.
See instructions for programming details.
HANDSET HOLDER
Used to temporarily hold the handset,
without hanging up the telephone,
when telephone is wall mounted.
HEARING AID COMPATIBLE HANDSET
HANDSET RETAINING CLIP
This removable clip can be rotated 180
degrees to allow handset to stay on hook
when used in wall mount applications.
HANDSET JACK
Modular jack for connecting handset to base.
DIAL KEYS (DTMF PAD)
For dialing phone numbers, and entering
numbers to be stored in auto dial keys.
FOR CUSTOMER SERVICE CALL
1-800-783-8353
Teledex, LLC
6311 San Ignacio Avenue
San Jose, CA
95119
Telephone: (408) 363-3100
Fax: (408) 363-3136
email: sales@teledex.com
Internet: www.teledex.com
LED Red/Flashing = Ringing Line
LED Red/solid = Line on HOLD
LED Green = Active Line
Part Number 606-0424-00