Filter
Top Products
key to scroll upwards. You may place a call to the number on the display
by either picking the handset or pressing the SPEAKER/HEADSET key.
5) Alternately, you may “jump” to a section of your phone book, without
having to scroll through the entire list, by entering the letter of the section
you wish to search. For example, you can jump directly to the “C” section
of your phone book (all names beginning with the letter “C”) by entering
the letter C on the key pad (press the number 2 three times in succession.)
6) To exit the directory at any time, press the PHONE BOOK key.
7) If a name and/or number has already been entered into the directory, the
B150D will prompt you that this listing already exists. The display will
read DUPLICATE, erase one of the duplicates and return to time display.
15) DELETING A NAME AND NUMBER IN THE DIRECTORY
1) Press the PHONE BOOK key. The display will show the first name and
number entered in the directory.
2) Using the REVIEW keys, scroll to the name and number you wish to
delete, and press the DELETE key.
3) The display will show the prompt DELETE?. Press the DELETE key
once, and this name and number will be erased from your phone book.
16) CONNECTING AN OPTIONAL HEADSET
Your B150D is equipped with a headset jack that allows you to connect an optional
headset, for convenient hands-free conversations. The jack accepts standard 2.5mm
headset plugs.
To use your headset:
1) Insert the headset’s plug into the headset jack, located on the right side of
the base (Refer to figure 6 below.)
2) Place the headset on your head, with the earpiece over either ear and
adjust the microphone boom until it is about even with your chin.
3) Press the SPEAKER/HEADSET key to make or receive calls.
4) When you finish a conversation, press SPEAKER/HEADSET to hang up.
17) ADJUSTING HEADSET VOLUME
When you pick up the headset to make or receive a call, the headset volume is preset
to a normal level. To increase or decrease the headset volume level, press the
VOLUME or VOLUME keys.
3rd, 2nd, or 1st number stored. Once you have scrolled to the right number, you
may dial the number by either pressing the SPEAKER/HEADSET key or picking up the
handset. Either action will initiate a call to the number in the display.
NOTES: The redial memory only stores the last 32 digits of any number dialed.
The redial memory does not store a LINK entry, but stores any digits you press after
FLASH/LINK (see “Using FLASH/LINK”.)
11.7 USING FLASH/LINK
FLASH/LINK performs the electronic equivalent of a hookswitch operation for
special services, such as call waiting. For example, if you have call waiting, press
FLASH/LINK to answer an incoming call without disconnecting the current call. Press
FLASH/LINK again to return to the first call.
CAUTION: If you do not have any special phone services, such as call waiting, etc., pressing the
FLASH/LINK key may disconnect the current call.
11.8 USING HOLD
To place a call on hold, press the HOLD key. The HOLD indicator will flash, then the
text message CALL ON HOLD will appear on the LCD. You can now hang up the hand-
set without disconnecting the call.
To resume the call, lift the handset (if the handset has been placed on the base) or
pick up any extension phone on the same line. If you put a call on hold while using
the speakerphone, press the SPEAKER/HEADSET key to resume the call.
NOTE: The B150D cannot receive an incoming call while a call is on hold.
11.9 USING MUTE
To temporarily switch off the microphone of either the speakerphone or handset,
press the MUTE key. The MUTE indicator lights and the microphone will turn off, but
you can still hear the person on the other end of the phone. Press MUTE again to
resume your conversation.
11.10 MEMORY DIALING
You can store up to ten (10) phone numbers and names in the direct memory locations,
then quickly and conveniently call a number you have stored These memory buttons
may also be used to store number strings used to access PBX or Centrex services or
features.
11.11 STORING A NUMBER IN MEMORY
Follow these steps to store numbers in the memory locations. Each memory location
can store up to sixteen (16) digits.
1) Press PRGM. The PROGRAM MODE prompt will appear.
2) Select the memory location where you want to store the number.
ENTER NUMBER will appear in the display.
3) Enter the phone number or number string you wish to store. If you enter
a digit by mistake, press DELETE to delete the last number entered.
Pressing DELETE once will delete the last digit, pressing twice will delete
the prior digit, etc.
4) When you are done entering the desired number, press the PRGM key.
5) The display will now read ENTER NAME. Press the letters on the
keypad corresponding to A through Z. (Please refer to Figure 5, “Keypad
Legend” on page 8.) To enter a space between letters, press the “1” key.
If you enter a letter by mistake, press the DELETE key. Pressing once will
delete the last letter, pressing twice, will delete the letter previous to it, etc.
6) Once the correct letters are entered, press the PRGM key. You will hear
10 7
Teledex B150D Users Manual
Teledex B150D Users Manual
DELETING DIRECTORY ENTRIES
FLASH/LINK
P/N 600-0480-52 Contents Copyright © 2002 Teledex LLC
FIGURE 6