Filter
Top Products
iPhone DECT Cordless Series User Guide
For Models AC8205S, AC8210S (1.8 GHz) and AC9205S, AC9210S (1.9 GHz)
Preparing to Use the AC8200/AC9200 Series
1. Prepare to install the battery into the cordless handset
by removing the battery cover and sliding it off. If cover is
secured with a screw, remove the screw first.
2. Insert the battery connector into the handset’s connector.
The connector is “keyed” so it only goes in one way.
Do not force the connection.
Note: The handset may “beep” when the battery is
connected. This is not an indication that the telephone
is ready to use. To obtain optimal performance of the
telephone, be sure to charge the battery for 10 to 12 hours.
3. Replace the battery compartment cover and the
retaining screw.
4. Insert the provided rubber screw cover.
5. Turn the telephone base so the back panel is facing you.
Insert either end of the RJ-45 cable into the jack on the
back of the telephone labeled LINE.
6. Insert the other end of the cable into the jack on the AC
adapter labeled PHONE.
7. Insert one end of the RJ-11 line cord into the jack on the
AC adapter labeled LINE.
8. Insert the other end of this line cord into a telephone jack.
9. Plug the AC adapter into an unswitched electrical outlet.
10. Remove the plastic overlay and place the paper faceplate
(supplied separately) over the keys. Replace the plastic
overlay by hooking the tabs on the overlay into the
recessed slots located on both sides.
11. Place the cordless handset on the base unit.
The handset/base registration process will occur.
Handset/Base Registration Procedure
This procedure establishes an exclusive link between a specific
handset and base, thereby allowing no other access to this
specific base. To accomplish this procedure, place the handset
on the base in the charging position. The LINE indicator will
blink while the registration process is occuring. This process
only occurs the first time a handset is placed on the charging
cradle of a new base.
Charging the Battery
The rechargeable Lithium-Polymer battery must be fully
charged before using the phone for the first time.
It is recommended that the battery be charged for approxi-
mately 10 to 12 hours without interruption before use.
To charge the battery, place the handset, keypad down, in the
base unit. Ensure that the CHARGE LED on the base lights.
If the LED Does Not Light:
1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is plugged into an unswitched
electrical outlet.
3. Ensure that the handset charging contacts at the bottom of
the handset are making good contact with the base unit’s
charging contacts.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all
charging contacts on the handset and base unit. Use a
pencil eraser or other contact cleaner. Do not use any
liquids or solvents.
Battery Safety Instructions
1. Use only Teledex-approved battery replacements.
2. Dispose of the Lithium-Polymer battery in any ordinary
trash receptacle.
3. Do not dispose of battery in fire, as it may explode.
4. Charge the battery only while in the handset, and only by
using the base unit to charge. Do not attempt to remove
the battery and charge it in a separate charging unit.
5. Do not short-circuit the battery, as this may cause it to
explode or catch fire.
Adjusting the Ring Volume and Assigning Ring Tones
The UP and DOWN volume keys will adjust the ringer volume
of the telephone. To adjust ring volume, press either the UP
and DOWN volume key when the handset is on the bse cradle
and the phone is not active (off-hook).
There are four ring tones that can be assigned individually
to either line (on two-line models) to audibly identify the
ringing line. Additionally, the AC8200/AC9200 series features
a programmable “crescendo” ring mode, wherein the ring
volume begins at the lowest setting, then rings progressively
louder with each ring during an incoming call.
To assign a ring tone to a line (normal ring mode):
1. Press the FLASH key (see Fig. 1); then a key on the dial pad
from 1-4, depending on the desired ring tone. The phone
will ring once to provide a sample of the selected ring
tone.
2. When you have selected a suitable ring tone, press the
STORE key (see Fig. 1), then a number on the dial pad for
the desired line assignment (i.e.; ‘1’ for line 1, ‘2’ for line 2).
Cordless Handset
AC Adapter
Base Unit
User Guide
Lithium Polymer Battery
Clear Plastic Overlay
Rubber Battery Screw Cover
Phillips Screw
15-foot, 8-wire Cable
(with RJ-45 connector)
10-foot, 4-wire Line Cord
(with RJ-11 connector)
Included in Your Package