Filter
Top Products
about 3 seconds until a series of
tones is heard. The Indicator
Light [2] will flicker for 1 second
and start flashing.
To turn the Headset off, press
and hold the On/Off Button [2] for
about 3 seconds until a series of
tones is heard. The Indicator
Light will flash, before turning off.
Changing Volume
To increase the volume, during a
call, press Vol+ Button [3]. To
decrease the volume, press the
Vol- Button [4]. The Headset will
remember all volume settings
even when it is switched off.
Accepting / rejecting* a call
When the phone rings (ring tone
can be heard in Headset), briefly
press the Multi-function Button
[2] once to accept the call. Press
and hold the Multi-function
Button [2] for 1 second to reject
the call.
Initiating a call from your
mobile phone
Dial the number as usual with
your phone. If your Headset is on
and the phone has been correct-
ly paired, your phone will transfer
the call to your Headset.
Initiating a call with voice dialling
You may be able to initiate the
voice dialling function from your
Headset (your phone will need to
support voice dialling and voice
tags need to be entered). To acti-
vate, briefly press the Multi-func-
tion Button [2]. You will then be
able to speak the name of the
person you wish to call.
Ending a call
Press the Multi-function Button
[2] briefly during a call and the
call will be ended.
Disconnecting from the phone*
You may wish to disconnect the
Headset from the phone in order
to reduce battery consumption.
To do so, press the Multi-func-
tion Button 3 times on the
Headset when it is not in an
active call. If you want to pick up
a call, you first need to re-con-
nect the Headset. To do so,
press the Multi-function Button
once again on the Headset.
Battery life
To conserve battery life, your
Headset features an auto-sleep
function. This function switches
the Headset off after 12 hours of
inaction. Once your Headset has
entered auto-sleep, it can be
switched on again normally.
When the battery has only 10%
charge remaining, the Headset
will produce an audible warning
tone sequence every time a call
is ended.
Resetting your Headset
Should your Headset stop res-
ponding, try charging it for a few
seconds. Your Headset should
now function again as normal.
5
Then complete normal pairing
process by following point 1
and 2 of the auto-pairing sec-
tion above.
3. WEARING AND CARRYING
THE HEADSET
You can wear your Headset on
either ear and carry it in different
ways using the rotating Multi-
function Arm [7].
Wearing the Headset without
the Ear Hook
You can wear the Headset with-
out using the Ear Hook. To do so:
1. Rotate the Multi-function Arm
[8] downwards, until it stays in
your ear like a wired headset
cable extension.
2. Gently place the Speaker [5]
into your ear canal.
3. Finally find the most comfort-
able position by rotating the
Headset forward and backward.
Wearing the Headset with
the Ear Hook
The Ear Hook may also be used
for maximum comfort. To mount
the ear hook, rotate the Multi-
function Arm [7] upwards and
slide it inside the Ear Hook [8]
jack. To place it on your ear fol-
low these steps:
1. Rotate the Ear Hook [8] slight-
ly forwards.
2. Gently place the Speaker [5]
into your ear canal.
3. Rotate the Ear Hook [8] back-
wards and adjust it behind your ear.
4. To switch from one ear to the
other, simply rotate the Multi-
function Arm [7] downwards and
rotate the Ear Hook [8] to the
opposite side.
Clipping your Headset to your
clothes
The Multi-function Arm can also
be used to carry your Headset in
several convenient ways (Ear
Hook not mounted). To clip it to
your clothes do the following:
1. Rotate the Multi-function Arm
[7] to the same direction of the
microphone [6]
2. Use the Multi-function Arm [7]
and Headset Body as a clip to
attach the Headset to your
clothes.
Using your Headset Cord to carry
your Headset
The Headset Cord [9] can also be
used to carry your Headset with
your mobile phone (Ear Hook not
mounted). To attach your
Headset to the Headset Cord [9]
follow these steps:
1. Rotate the Multi-function Arm
[7] until it is in opposite direction
of the Headset microphone [6]
2. Attach the Multi-function Arm
[7] to the Headset Cord [9] jack
4. GENERAL USAGE
Turning the Headset on and off
To turn the Headset on, press
and hold the On/Off Button [2] for
4
* The features marked with an asterisk will only work with Bluetooth phones which support the Hands-free profile.
Today, most Bluetooth phones support this profile.
User guide_SH440.qxd 22/12/2006 16:09 Seite 4