Filter
Top Products
SPP Q110/Q120 3 856 344 11 E U
Prepare the battery pack
Insert the battery into the handset and charge first before you start
using your phone.
1Slide open the battery compartment lid of
the handset.
2Connect the battery connector with correct
porality (black and red cords).
3Insert the battery pack, and close the lid.
4Place the handset on the base unit.
The CHARGE lamp lights up when the
handset is properly seated on the charge
terminals of the base unit. Charge the
battery pack for more than 12 hours so that
the battery is fully charged. The CHARGE
lamp remains lit even after charging is
completed.
Battery duration
A fully charged battery pack lasts for about:
• 12 hours when you use the handset continuously
• 14 days when the handset is standing by.
Notes
• The battery pack will gradually discharge over a long
period of time, even if not in use.
• The battery works best when charged every two or three
days. For best performance, do not return the handset to
the base unit after every call.
If the battery runs out completely, the speed dial
numbers and the digital security code will be erased. If
this happens, charge it on the base unit for over 12 hours.
Then reprogram the speed dial numbers, and assign a
new digital security code (see “Resetting the digital
security code”). You may need to charge the battery
several times before it is recharged to its full capacity.
When to purchase a new battery pack
If the battery lasts only a few minutes even after 12 hours of charging, the usable
life of the battery has expired and needs replacement. Contact your local Sony
authorized dealer or service center, and ask for Sony BP-T16 rechargeable battery
pack.
Notes
• Do not cover the microphone during the conversation; otherwise, the other party cannot
hear your voice.
• If you hear beeps during the conversation, move closer to the base unit; otherwise, the
call will be disconnected after 15 seconds. Note that, however, you may not hear beeps if
it’s noisy on the handset.
If interference occurs on the handset
When you press (TALK), the handset automatically searches for the channel with
the best reception. However, if you notice interference during a conversation,
move closer to the base unit.
If interference persists, press (CHANNEL) to switch to another channel to improve
the sound quality of your telephone conversation.
Note
If you hear five short beeps when you press (CHANNEL), move closer to the base unit.
If the handset battery becomes weak during a call
The handset will beep every three seconds with the TALK/BATT LOW lamp
flashing at the same time. Finish your call and charge the battery pack.
Caution
If this occurs, you cannot use the handset without charging it for more than 1 minutes.
Redialing
1 Press (TALK), and wait until the TALK/BATT LOW lamp lights up.
2 Press (REDIAL/PAUSE) to redial the number last dialed.
Note
If the number exceeds 32 digits, the beeps will alert you that the number can’t be dialed.
To erase the last phone number dialed
Press (REDIAL/PAUSE) twice.
The number will be erased from the memory, and you’ll hear a long confirmation
beep.
Speed dialing
You can dial with a touch of a few keys by storing a phone number on a dialing
key.
Storing phone numbers
1 Press (PGM).
The TALK/BATT LOW lamp flashes.
2 Press (SPEEDDIAL).
The dialing keys light up (SPP-Q120
only).
3 Press one of the dialing keys ((0) to
(9)) to store a phone number on.
You hear a confirmation beep.
4 Enter the phone number you want to
store.
You can enter up to 16 digits,
including a tone and a pause, each of
which is counted as one digit.
5 Press (PGM).
You hear a long confirmation beep,
and the number is stored. The TALK/
BATT LOW lamp goes off.
Note
Do not allow more than 20 seconds to elapse between each
step of the procedure.
Tips
• If you enter a wrong number, press (PGM), then start
from the beginning.
• You can attach the supplied directory on the handset.
• You can’t receive calls while you’re storing numbers.
To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in Step 4, do as follows:
1 Enter the outside line access digit (e.g., 9).
2 Press (REDIAL/PAUSE).
Do this
Press (FLASH).
Press the button again to get back to the first caller.
To
Switch to another call*
("call waiting" service)
Additional tasks
* You need to subscribe to this service from your telephone company.
1
2
3
4
CHARGE
lamp
Red
Making and receiving calls
Making calls
1 Pick up the handset from the base
unit.
2 Press (TALK), and wait until the
TALK/BATT LOW lamp lights up.
The dialing keys light up (SPP-Q120
only).
You then hear a dial tone. If you hear
beeps, move closer to the base unit.
3 Dial the phone number.
4 When you're done talking, press
(OFF).
The TALK/BATT LOW lamp goes
off.
Additional tasks
Do this
Press TONE (*) after you’re connected.
The line will remain in tone dialing until disconnected.
To
Switch to tone dialing
temporarily
Receiving calls
1 When you hear the phone ring;
• Press (TALK) (or any key except (OFF)).
or
• Pick up the handset from the base unit when the handset is
placed on the base unit.
The TALK/BATT LOW lamp lights up.
2 When you’re done talking, replace the handset on the base unit or
press (OFF).
The TALK/BATT LOW lamp goes off.
TONE(*)
(REDIAL/PAUSE)
(CHANNEL)
Microphone
(FLASH)
TALK/BATT
LOW lamp
Black
(REDIAL/PAUSE)
TALK/BATT
LOW Lamp