Filter
Top Products
1. Make sure the phone is ON.
2. Press memory and then press 7.
3. When you hear the access tone, press memory again and then
press 8.
4. At the next access tone, press memory and then 9.
TIP: Wait for the access tones between pressing the memory
button, or your call might not go through.
CHANGING THE BATTERY
Make sure the telephone is OFF before you
replace battery.
1. Remove the battery compartment door.
2. Disconnect the battery plug from the jack in
the handset battery compartment and remove
the battery pack.
3. Insert the new battery pack and connect the
cord into the jack inside the handset.
4. Put the battery compartment door back on.
5. Place handset in the base to charge. Allow
the handset battery to properly charge (for 12 hours) prior to
first use or when you install a new battery pack. If you do
not properly charge the phone, battery performance will be
compromised.
CAUTION: To reduce the risk of fire or personal injury,
use only the battery 5-2461.
BATTERY SAFETY PRECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like other
batteries of this type, toxic materials could be released which
can cause injury.
• To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
GENERAL PRODUCT CARE
To keep your telephone working and looking good, follow
these guidelines:
• Avoid putting the phone near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping and other rough treatment to the phone.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because
this will damage the finish.
• Retain the original packaging in case you need to ship the
phone at a later date.
CAUSES OF POOR RECEPTION
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction can shield radio signals.
• You’re too close to appliances such as microwaves, stoves,
computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the house.
• Base is plugged into an AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You’re out of range of the base.
6. Use the number keypad to enter the telephone number you
want to store (up to 24 digits).
7. Press memory again to store the number. You will hear a
confirmation tone.
CHANGING A STORED NUMBER
1. Repeat steps 1 through 7 in Storing a Name and Number
in Memory.
2. Press the memory button and REPLACE MEMO? shows in
the display.
3. Press the * tone/exit button to exit, or press the memory
button to store the number. You will hear a confirmation tone.
STORING A REDIAL NUMBER
1. Repeat steps 1 through 6 in Storing a Name and Number
in Memory.
2. Press the redial button.
3. Press the memory button to store the number. You will hear a
confirmation tone.
To replace an old redial number stored in a memory locations
with a new redial number:
1. Repeat steps 1 through 6 in Storing a Name and Number
in Memory.
2. Press the memory button and REPLACE MEMO? shows in the display.
3. Press the * tone/exit button to exit, or press the memory button
again and the new redial number replaces the old redial number
in that memory location. You will hear a confirmation tone.
DIALING A STORED NUMBER
1. Make sure the phone is ON by pressing the SPEAK/END button.
2. Press memory button.
3. Press the number (0-9) for the desired memory location. The
number dials automatically.
- OR -
1. Make sure the phone is OFF (not in TALK mode).
2. Press memory button.
3. Use the CID/VOL (-) arrow or CID/VOL (+) arrow button to
scroll through the numbers stored in memory until the desired
number is shown.
4. Press the SPEAK/END button. The numbers dial automatically.
IMPORTANT: If you make test calls to emergency numbers
stored in memory, remain on the line and briefly explain the
reason for the call to the dispatcher. Also, it’s a good idea to
make these calls in off-peak hours, such as early morning or
late evening.
INSERTING A PAUSE IN THE DIALING SEQUENCE
When storing information in memory, press the # pause button
twice within one second to insert a delay in the dialing sequence
of a stored telephone number when a pause is needed to wait for
a dial tone (for example after you dial 9 for an outside line, or to
wait for a computer access tone). PAUSE shows on the display as
a P. Each pause counts as 1 digit in the dialing sequence.
REVIEWING AND DELETING STORED NUMBERS
1. Press memory, then use the CID/VOL (-) arrow or CID/VOL (+)
arrow button to view the entry.
2. While the entry is displayed, press channel/delete button to
delete the entry. The display shows DELETE?
3. Press channel/delete again to delete the entry. DELETED shows
in the display.
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently called long
distance number. Basically, you dial each part of the sequence
from memory. The following example shows how you can use
chain dialing to make a call through a long distance service:
The Number For Memory Location
Long distance access number 7
Authorization code 8
Frequently called long distance number 9
DESCRIPTION
MODEL NO.
Replacement battery
ACCESSORY INFORMATION
Power adaptor
white
5-2461
5-2558
To place order, have your Visa, MasterCard, or Discover
Card ready and call toll-free 1-800-338-0376.
A shipping and handling fee will be charged upon ordering.
We are required by law to collect appropriate sales tax for
each individual state, country, and locality to which the
merchandise is being sent.
Items are subject to availability.
*Prices are subject to change without notice.
DISPLAY MESSAGES
The following indicators show the status of a message or of the unit.
INCOMPLETE DATA Caller information has been interrupted
during transmission or the phone line is
excessively noisy.
ENTER NAME Prompt telling you to enter the name for
one of the 10 memory locations.
ENTER TEL NUMBR Prompt telling you to enter the telephone
number for one of the 10 memory locations.
DELETE? Prompt asking if you want to erase Caller
ID records or one of the 10 numbers stored
in the phone’s outgoing memory.
DELETE ALL? Prompt asking if you want to erase all
Caller ID records.
DELETED Prompt confirming the Caller ID /Memory
record is erased.
END OF LIST Indicates that there is no additional
information in Caller ID memory.
NEW Indicates call or calls have not been reviewed.
UNKNOWN NAME/ The incoming call is from an area not
CALLER/NUMBER serviced by Caller ID or theinformation was
not sent.
PAGING Someone has pressed the FETCH! button on
the base.
BLOCKED CALL The person is calling from a number that
has been blocked from transmission.
BLOCKED NAME The person’s name is blocked from transmission.
REPT Repeat call message. Indicates that a new
call from the same number was received
more than once.
NO DATA No Caller ID information was received.
EMPTY Indicates a memory location is vacant.
NO CALLS Indicates no CID records have been stored.
MESSAGE WAITING Indicates a message is available.
HANDSET SOUND SIGNALS
Signal Meaning
A long warbling tone Signals an incoming call
(with ringer on)
Two long beeps Confirmation Tone
One short and one long beep Page signal
One short beep every seven seconds Low battery warning
TROUBLESHOOTING TIPS
CALLER ID
No Display
• Is battery fully charged? Try replacing the battery. Make sure
the battery is properly installed and connected.
• If you are using AC power, make sure that the unit is
connected to a non-switched electrical outlet. Disconnect the
unit from the plug and plug it in again.
• Did you order Caller ID service from your local telephone company?
Caller ID Error Message
• The unit displays this message if it detects anything other
than valid Caller ID information during the silent period
after the first ring. This message indicates the presence of
noise on the line.
TELEPHONE
No dial tone
• Check installation:
— Is the base power cord connected to a working outlet?
— Is the telephone line cord connected to the base unit and the
wall jack?
• Disconnect the base from the wall jack and connect another
phone to the same jack. If there is no dial tone in the second
phone, the problem might be your wiring or local service.
• Is the handset out of range of the base?
• Make sure the battery is properly charged (12 hours).
• Is the battery pack installed correctly?
• Did the handset beep when you pressed the SPEAK/END
button? Did the display indicator turn on? The battery may
need to be charged.
Dial tone is OK, but can't dial out
• Make sure the tone/pulse setting is programmed correctly.
Handset does not ring
• Make sure the ringer switch on the handset is turned to ON.
• You may have too many extension phones on your line. Try
unplugging some phones.
• See solutions for “No dial tone.”
Charge • In Use indicator on the base flashes
• Provided your phone company offers voice messaging service and
you subscribe to it, the charge • in use indicator on the base
flashes when the phone is not in use to indicate there is a message
waiting. It stops flashing after the message has been reviewed.
You experience static, noise, or fading in and out
• Change channels.
• Is handset out of range? Move closer to the base.
• Does the base need to be relocated?
• Charge battery.
• Make sure base is not plugged into an outlet with another
household appliance.
Unit beeps
• Place handset in base for 20 seconds to reset the security
code. If that doesn’t work, charge battery for 12 hours.
• See solutions for “No dial tone.”
• Replace battery.
Memory Dialing
• Did you program the memory location keys correctly?
• Did you follow proper dialing sequence?
• Make sure the tone/pulse setting is programmed correctly.
• Did you reprogram numbers into memory after power outage
or battery replacement?
LIMITED WARRANTY
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase.
(The warranty period for rental units begins with the first rental
or 45 days from date of shipment to the rental firm, whichever
comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The
exchange unit is under warranty for the remainder of the original
product’s warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were
originally provided with the product. We recommend using the
original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted
invoice which is evidence that the product is within the warranty
period, must be presented to obtain warranty service.” For rental
firms, proof of first rental is also required. Also print your name
and address and a description of the defect. Send via standard
UPS or its equivalent to:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service
not covered by the warranty.
• Insure your shipment for loss or damage. ATLINKS accepts no
liability in case of damage or loss.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty does not cover:
• Customer instruction. (Your Ueser’s Guide provides information
regarding operating instructions and user controls. Any additional
information, should be obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into
other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed
with your unit. It will make it easier to contact you should it
ever be necessary. The return of the card is not required for
warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL
CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF
THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC.
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR
ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE
STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of
incidental or consequential damages, or limitations on how long
an implied warranty lasts so the above limitations or exclusions
may not apply to you.
• This warranty gives you specific legal rights, and you also may
have other rights that vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for
warranty information.
S
ERVICE
If trouble is experienced with this equipment, for repair or warranty
information, please contact customer service at 1-800-511-3180. If
the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment
until the problem is resolved.
This product may be serviced only by the manufacturer or its
authorized service agents. Changes or modifications not expressly
approved by ATLINKS USA, Inc. could void the user’s authority to
operate this product. For instructions on how to obtain service,
refer to the warranty included in this guide or call customer
service at 1-800-511-3180.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or
jot down the date this product was purchased or received as a
gift. This information will be valuable if service should be
required during the warranty period.
Purchase date
_________________________________________
Name of store
_________________________________________
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna
for radio or television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet
on a circuit different from that to which the receiving
antenna is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
If these measures do not eliminate the interference, please
consult your dealer or an experienced radio/television technician
for additional suggestions. Also, the Federal Communications
Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available
from the U.S. Government Printing Office, Washington, D.C.
20402. Please specify stock number 004-000-00345-4 when
ordering copies.
NOTE: The RBRC seal on the battery used in
your ATLINKS USA, Inc. product indicates
that we are participating in a program to
collect and recycle Nickel Cadmium batteries
throughout the United States. Please call
1-800-8-BATTERY for information or contact
your local recycling center.
Ni-Cd
RBRC
R
B
R
C