Filter
Top Products
©2005. RadioShack Corporation.
All rights reserved. RadioShack and
RadioShack.com are trademarks
used by RadioShack Corporation.
43-3904
A
06A05
NLM052Y1
Printed in China
Your phone is hearing aid compatible.
Your telephone complies with Part 68 of FCC Rules and the requirements adopted
by the ACTA. On the back of this product is a label with this product’s FCC Product
Identification number in the format DYFMT08B433904. If requested, you must
provide this information to the telephone company.
Note: You must not connect your telephone to:
•..coin-operated systems
•..most electronic key telephone systems
•..party-line systems
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission, or corporation commission for
information.
We have designed your telephone to conform to federal regulations, and you can
connect it to most telephone lines. However, each telephone (and each device,
such as a telephone or answering machine) that you connect to the telephone
line draws power from the telephone line. We refer to this power draw as the
device’s ringer equivalence number, or REN. The REN for your telephone is the
digits represented by #.#, without a decimal point (e.g., 03 is a REN of 0.3), in the
Product Identification number found on the bottom of your telephone.
If you use more than one phone or other device on the line, add up all of the
RENs. If the total is more than five (three in rural areas), your telephones might not
ring. If ringer operation is impaired, remove a device from the line.
In the unlikely event that your phone causes problems on the phone line, the
phone company can temporarily discontinue your service. If this happens, the
phone company attempts to notify you in advance. If advance notice is not
practical, the phone company notifies you as soon as possible and advises you of
your right to file a complaint with the FCC.
Also, the phone company can make changes to its lines, equipment, operations,
or procedures that could affect the operation of this telephone. The telephone
company notifies you of these changes in advance, so you can take the necessary
steps to prevent interruption of your telephone service.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult your local RadioShack store or an experienced radio/TV technician for help.
• If you cannot eliminate the interference, the FCC requires that you stop using your
telephone.
Changes or modifications not expressly approved by RadioShack may cause
interference and void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Consult your local RadioShack store or an
experienced radio/TV technician for help.
If you cannot eliminate the interference, the FCC requires that you stop using your
telephone. Changes or modifications not expressly approved by RadioShack may
cause interference and void the user’s authority to operate the equipment.
FCC statement
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for
one (1) year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees
and dealers. For complete warranty details and exclusions, check with your local RadioShack store.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102 04/04
limited one-year warranty
using the phone
If your telephone is not performing as it should, take it
to your local RadioShack store for assistance. To locate
your nearest RadioShack, use the store locator feature
on RadioShack’s website (www.radioshack.com), or call
1-800-The Shack (843-7422) and follow the menu options.
Modifying or tampering with the telephone’s internal
components can cause a malfunction and might invalidate
its warranty and void your FCC authorization to operate it.
service and repair
Your telephone connects directly to a modular telephone
line jack. If your telephone wiring does not have a modular
jack, you can update the wiring yourself using jacks and
adapters (available at your local RadioShack store), or have
the telephone company update the wiring for you. You must
use compatible modular jacks that are compliant with Part
68 of FCC Rules and the requirements adopted by the ACTA.
The telephone cord and modular plug provided is Part 68
compliant for connecting to the telephone company network.
The USOC number of the jack to be installed is
RJ11C (or RJ11W for a wall plate jack).
If your home has specially wired alarm equipment connected
to the telephone line, be sure that installing the telephone
does not disable your alarm equipment. If you have
questions about what will disable your alarm equipment,
contact your telephone company or a qualified installer.
set up
caller ID operation
making a call
1. Pick up the handset and wait for a dial tone.
2. Use the keypad to enter the number you wish to
dial. The dialed number appears on the display. If
you dial a number over 15 digits, only the last 14
digits appear on the display.
3. When you complete your call, hang up. A few
seconds later, the number disappears, and the
display returns to normal.
receiving a call
When you receive a call, the phone rings and NEW
flashes. NEW and the caller’s number appear on the
display. To answer the call, pick up the handset. NEW
flashes until you have reviewed all calls.
using timer
Your clock timer counts up to 60 minutes in the off-
hook time (00:00 format). The timer starts to count up
when you dial a number or answer incoming calls.
If you lift the handset and don’t dial a number, the timer
appears and starts to count up after 10 seconds.
using pause
When you manually dial a number, you can have
your telephone pause anywhere during the dialing
sequence. Simply press REDIAL/PAUSE at the desired
location, and P appears on the display next to the
dialed number.
• Redial memory holds up to 32 digits, so you
can redial long distance, as well as local phone
numbers.
• When you redial a number, the telephone pauses
for about four seconds at the pause entry. For long
pauses, press REDIAL/PAUSE again.
• If you do not have any special phone services,
press FLASH might disconnect the current call.
• The LCD backlight turns on when the handset is
picked up or any key is pressed; it turns off
if no key
is pressed within 10 seconds.
• The keypad’s backlight turns on if you pick up the
handset. It only turns off when you hang up the
phone.
If you subscribe to a Caller ID service, the phone
automatically displays information about calls you
receive and stores the information in memory. The
system can store up to 99 incoming phone numbers and
incoming names into call records.
• During an incoming call, the phone company
automatically sends the correct time between the
first and second rings to update your system’s
display.
• After reviewing all calls, the system resets so that
the display shows 0 new calls.
reviewing call records
1. Repeatedly press ( or ) to review the new calls. END
OF NEW CALL appears when all calls have been reviewed.
2. To review all the records from oldest to newest,
repeatedly press REVIEW ).
To review the records from newest to oldest,
repeatedly press (REVIEW. After reviewing all records
in memory,
END OF LIST appears.
3. If an incorrect, invalid or
incomplete Caller ID signal
is received, LINE ERROR
appears on the display.
If the name and number
are not available due to
the caller’s restriction,
PRIVATE CALL
appears on the
display.
If the name and number are
not available, -UNAVAILABLE- appears on the display.
RPT appears beside a number if you have received a
call from the same phone number more than once.
4. If you do not press a button within about 15 seconds,
the system automatically returns to the normal
display.
call back from caller ID memory
1. With the handset on the base, press ( or ) to find
the number to redial.
2. Press CALL BACK twice. PICK UP CALL appears.
3. Lift the handset, and the number is automatically
redialed.
Select one of the four options
below based on your telephone
company’s requirements to make
toll calls within your area code.
Option 1
1 + Area Code + 7-digit number
(11 digits)
Option 2
1 + 7-digit number (8 digits)
Option 3
Area Code + 7-digit number (10 digits)
Option 4
7-digit number
1. With the handset on the base, press
( or ) to find
the number to redial.
2. Press CALL BACK. The 7- or 11-digit number
flashes.
3. Press
( or ) to select one of the above four
options.
4. Press CALL BACK again to confirm.
5. Pick up the handset, and the selected number is
dialed automatically.
• When the caller’s phone number has a
different area code from the preset area
code, 1 and the caller’s three digit area code
are inserted automatically during memory
call back.
• When the caller’s phone number has
the same area code as the preset one, 1
and the three digit area code are deleted
automatically during the memory call back.
NOTE
NOTE
You can delete an individual call record, or all call records stored in the system.
To delete a single call record, press
( or ) until the call record you want to delete appears, then press DELETE twice.
The record is deleted, and the remaining call records are automatically renumbered.
To delete all of the call records after reviewing all new calls, hold down DELETE for about three seconds. ERASE ALL
CALLS appears. Press
DELETE. The system deletes all call records, NO CALLS appear, then TOTAL:00 NEW:00 appears.
• When the phone’s memory is full, it automatically replaces the oldest call record with the newest incoming call.
• If you do not press any button within about 15 seconds while the display shows ERASE ALL CALLS, the phone
automatically returns to normal display and the call records are not deleted.
Your telephone is CETL listed and meets all applicable Canadian standards.
deleting call records
NOTE
Your telephone has built-in protection circuits to reduce
the risk of damage from surges in telephone line and
power line current. These protection circuits meet or
exceed the FCC requirements. However, lightning striking
the telephone or power lines can damage your telephone.
Lightning damage is not common. Nevertheless, if you live
in an area that has severe electrical storms, we suggest
that you unplug your phone when storms approach to
reduce the possibility of damage.
surge protection
Notes
NOTE