Filter
Top Products
4
5. Lift the base’s antenna to a vertical
position.
10"#"9#..
To mount the phone directly on a wall, you
need two screws (not supplied) with heads
that fit into the keyhole slots on the bottom of
the base.
1. Drill two holes 3
15
/
16
inches (100 mm)
apart. Then thread a screw into each
hole, letting the heads extend about
1
/
8
inch (3 mm) from the wall.
2. Plug one end of the supplied long
modular cord into the
TEL LINE
jack on
the back of the base.
3. Insert the supplied AC adapter’s barrel
plug into the
DC IN 9V
jack on the back of
the base.
4. Route the adapter and modular cords
through the grooves on the bottom of the
base.
5. Align the base’s keyhole slots with the
mounting screws and slide the base
downward to secure it.
6. Plug the modular cord’s other end into
the phone jack, and plug the adapter into
a standard AC outlet.
7. Lift the base’s antenna to a vertical
position.
%100'%6+0)1%*#4)+0)"6*'"
$#66'4;"2#%-
The phone comes with a rechargeable nickel-
cadmium battery pack in the handset, but not
connected. Before using your phone, you
must connect the battery pack, then charge it
for about 15
–
20 hours.
#
1. Press down and slide off the battery
compartment cover.
2. Lift the battery pack out of the
compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the
connector fits only one way), then place
the battery pack in the compartment.
4. Replace the cover.
To charge the battery pack, place the
handset face-up or face-down on the base.
The CHARGE/IN USE indicator on the base
lights and
JejWb0&&
JejWb0&&JejWb0&&
JejWb0&&
appears on the handset
display.
Recharge the battery pack when
Bem
BemBem
Bem
8Wjj[ho
8Wjj[ho8Wjj[ho
8Wjj[ho
flashes on the display.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
R
RR
Rý
ýý
ý
"
#"
4'%*#4)+0)"6*'"$#66'4;"2#%-
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear an error tone when you press
TALK
.
While holding
PAGE
, return the handset
to the base for about 3 seconds to reset
the security access-protection code.
• If the base loses power for about an hour
while the handset is away from it, the
security access-protection code might be
lost. To reset the code, while holding
PAGE
, return the handset to the base for
about 3 seconds.
• If the battery pack becomes weak during
a call, the handset beeps every 3
seconds and
Bemý8Wjj[ho
Bemý8Wjj[hoBemý8Wjj[ho
Bemý8Wjj[ho
flashes. When
this happens, you cannot make a call
until you recharge the battery pack.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• About once a month, fully discharge the
battery by keeping the handset off the
base until
Bemý8Wjj[ho
Bemý8Wjj[hoBemý8Wjj[ho
Bemý8Wjj[ho
flashes on the
display. Otherwise, the battery pack
loses its ability to fully recharge.
• The handset loses its security access-
protection code if the battery pack is
completely discharged. While holding
PAGE
, place the handset on the base to
recharge the battery pack and reset the
code.
• Using a pencil eraser, clean the charging
contacts on the handset and base about
once a month.
• If you are not going to use your phone
for an extended period, disconnect the
battery pack. This increases the battery
pack’s usable life.
• The supplied battery pack should last for
about a year. If the battery pack does not
hold a charge for more than 2 hours after
an overnight charge, replace it with a
new 3.6-volt, 600 mAh battery pack with
a connector that fits the socket in the
battery compartment. You can order a
replacement battery pack through
RadioShack. Install the new battery pack
and charge it for about 15
–
20 hours.
5'66+0)"6*'"4+0)'4"610'"#0&"
81.7/'
You can select one of five different ringer
tone/volume settings on the handset. Lift the
handset and repeatedly press
VOL
8
or
9
to select the desired ringer setting. Each time
you press the button, the phone rings at the
#
"+/2146#06"
#
• The EPA certified RBRC
®
Battery Recycling Seal on the
nickel-cadmium (Ni-Cd) battery
indicates RadioShack is
voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alternative to placing used Ni-Cd
batteries into the trash or the municipal
waste stream, which may be illegal in your
area. Please call 1-800-THE-SHACK (1-800-
843-7422) for information on Ni-Cd battery
recycling and disposal bans/restrictions in
your area. RadioShack’s involvement in this
program is part of the company’s
commitment to preserving our
environment
and
conserving our natural resources.
• Be sure the battery pack is properly
connected before you try to charge it. The
CHARGE/IN USE indicator lights when the
handset is on the base, even if the battery
pack is not connected.
ý
R
"9#40+0)"
R
"
Dispose of the old battery pack promptly and
properly. Do not burn or bury it. See “Battery
Safety Instructions” on Page 8 for additional
information on proper battery handling.