Filter
Top Products
4
Using the Alarms Section 4
The charger unit features an alarm clock. You can set the alarm to
play the radio or to sound a buzzer at a set time.
The radio alarm and the buzzer alarm can be set separately.
For assistance, please call: 1-800-211-PANA(7262)
[OFF]
[
-
, TUNE/CLOCK]
[AM/FM, RADIO]
Memory Buttons ([M1], [M2], [M3], [M4] and [M5])
[SNOOZE/MUTE]
[RADIO, ALARM DISPLAY/SET]
[BUZZER, ALARM DISPLAY/SET]
VOLUME
Control
[+, TUNE/CLOCK]
4-A Setting the Radio Alarm
1
Press [AM/FM, RADIO] to turn the radio on.
2
Press [AM/FM, RADIO] to switch between AM and FM.
3
Tune in to the desired station by pressing [–, TUNE/CLOCK] or
[+, TUNE/CLOCK].
OR
Press the desired memory button ([M1] to [M5]).
4
Adjust the volume by using the VOLUME control.
5
Press and hold [RADIO, ALARM
DISPLAY/SET] (the button on the top of
the unit) until the time flashes.
6
Set the alarm time by pressing
[–, TUNE/CLOCK] or [+, TUNE/CLOCK].
• Pressing and holding [–] or [+] changes
the time faster.
7
Press and release [RADIO, ALARM DISPLAY/SET] to save the
radio alarm time and the station.
• The time stops flashing and returns to the current time.
• “ ” is displayed while the radio alarm is turned on.
8
Press [OFF] to turn the radio off.
• The radio will automatically turn on at the set time and will turn off
after 1 hour.
•You can exit alarm setting mode any time by pressing [OFF].
•The buzzer will sound at the set radio alarm time if you did not turn
the radio on in step 1.
•To change only the radio alarm time, repeat steps 5 to 7.
•If a power failure occurs, the radio alarm time and station preset will
be retained for about 10 minutes.
To confirm the radio alarm time and station:
Press and release [RADIO, ALARM DISPLAY/SET].
•The alarm time and the station will be displayed for about 3 seconds.
To stop the alarm temporarily (SNOOZE)
Press [SNOOZE/MUTE].
•The alarm will then start again in 6 minutes. You can press
[SNOOZE/MUTE] again to stop the alarm.
To stop the alarm for the day
Press [OFF].
•The setting remains and the alarm will sound daily until you stop
the alarm completely. “ ” and/or “ ” will remain on
the display.
To stop the alarm completely
1. While the alarm is sounding or the SNOOZE mode is on, press
[OFF], then follow step 2.
OR
If the alarm is not sounding or the SNOOZE mode is not used, go
to step 2.
2.
Press [RADIO, ALARM ON/OFF] or [BUZZER, ALARM ON/OFF]
to turn the alarm off.
•“ ” or “ ” disappears from the display.
•To turn the alarm on again, press [RADIO, ALARM ON/OFF]
or [BUZZER, ALARM ON/OFF].
4-B Setting the Buzzer Alarm
1
Press and hold [BUZZER, ALARM
DISPLAY/SET] (the button on the top of
the unit) until the time flashes.
2
Set the alarm time by pressing
[–, TUNE/CLOCK] or [+, TUNE/CLOCK].
• Pressing and holding [–] or [+] changes the time faster.
3
Press and release [BUZZER, ALARM DISPLAY/SET] to save
the buzzer alarm time.
• The time stops flashing and returns to the current time.
• “ ” is displayed while the buzzer alarm is turned on.
• The buzzer will start at the set time and will automatically stop
after 10 minutes.
•You can exit alarm setting mode any time by pressing [OFF].
•If a power failure occurs, the buzzer alarm time will be retained for
about 10 minutes.
To confirm the buzzer alarm time:
Press and release [BUZZER, ALARM DISPLAY/SET].
•The alarm time will be displayed for about 3 seconds.
[OFF]
[RADIO, ALARM ON/OFF]
[BUZZER, ALARM ON/OFF]
[SNOOZE/MUTE]
4-C Stopping the Alarm
When the alarm sounds at the set time, “ ” is displayed and
“ ” and/or “ ” flashes.