Filter
Top Products
ABOUT YOUR PHONE
M5050 User guide.doc Page 5 of 6
6 Multi-handset use
Your M5000 series phone can have up to 5 handsets registered to 1 base unit. Each handset has its own
number HS-1, HS-2, HS-3, HS-4, & HS-5 shown on the left-hand side of the display.
With 2 or more handsets you can:
Make an intercom call
1. Press INTERCOM button. When you hear your outgoing message, press
2. Key the handset number 1, 2, 3, 4, OR 5, you wish to call.
3. On the RECIEVING handset, press PHONE button.
4. To end, press PHONE button on the CALLING handset. The RECIEVING handset will hear a busy tone.
Transfer a call between handsets
1. Press INTERCOM button.
2. Key the handset number 1, 2, 3, 4, OR 5, you wish to call.
3. On the RECIEVING handset, press PHONE button to receive call.
4. Press PHONE button on the CALLING handset to transfer. Call will return back within 90 seconds if
unanswered.
Switch between calls
An outside call + an intercom call in progress, you switch between the 2 calls:
1. Press INTERCOM button to speak to outside call, while the intercom call is on hold.
2. Press INTERCOM button again to speak to intercom call, while outside call is on hold.
3. Press PHONE to transfer outside call to the other handset (while connected to intercom call).
Conference calls
A 3-way call between yourself + outside call + intercom call:
1. Either make or answer an outside call.
2. Press INTERCOM button.
3 Key in the other handset number 1, 2, 3, 4, OR 5.
4. On the RECIEVING handset, press PHONE button to receive call.
5. Press INTERCOM button & hold for about 3 seconds.
5. When connected both symbols are shown on display
Notes
• A maximum of 1x outside call & 2x intercom calls can take place per base unit.
• If you make an outside call + another handset is on line = result is a busy tone.
• If you make an intercom call + one is already in progress = result is a busy tone.
Note
• If you press the PHONE button while connected to the outside call, you will disconnect
• If the other handset user presses the PHONE button to hang up, you will be left with the outside call
ABOUT YOUR PHONE
M5050 User guide.doc Page 6 of 6
7 Notes for operation in New Zealand
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted
that the item complies with the minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item of Telepermitted equipment of
a different make or model, nor does it imply that any product is compatible with all of Telecom’s network
services. This device may be subject to ringing or bell tinkle when certain other devices are connected to
the same line. If this occurs, the problem should not be referred to the Telecom Faults service.
This equipment shall not be set to make automatic calls to the Telecom “111” Emergency Service. This
equipment may not provide for the effective hand-over of a call to another device connected to the
same line.
REN (RN for New Zealand)
The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1
telephone to your telephone line. A standard telephone line has a maximum REN capacity of 3 (RN of 5). It
is possible to connect 3(5) devices with a REN of 1 (RN of 1) with no degradation to the product’s
performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring
at all.
Caller ID
Customers in NZ using NON-TELECOM toll services should not use the ‘dial back’ feature for local calls as this
will incur a charge only the 7 digit number should be dialled. Some of the CID services listed may not be
available in New Zealand. This telephone is NOT designed for making emergency telephone calls when the
power fails. Ensure there are alternative arrangements for access to emergency services via a mobile
phone or a corded telephone.
8 Warranty Information
This product is covered by a 12 month warranty against defective workmanship or parts. The warranty does
not extend to damage caused by misuse, negligence, excessive voltage, faults on the telephone line or
lightning. This guarantee in no way affects your statutory rights. Full details of the warranty are contained in
the enclosed warranty card. If you feel this product is not working correctly please consult the user guide and
ensure that you are using the product in accordance with the instructions. Remove all extra telephone
equipment and connect only this telephone directly to the telephone socket.
If the fault is still present, connect another telephone (if available) to the telephone socket. The results will
show you whether the fault lies with this unit or with the telephone line. If the product is working correctly
the fault is on the telephone line. Please contact your network operator for assistance
To orders spare parts additional handsets, replacement batteries and in case of any technical
issues you may have with product please consult our website for further information or send us an
email for a prompt response to your enquiry. In the unlikely event of a fault developing, please
contact us for assistance. If the product is then found to be faulty you will be asked to return it
directly to us with a copy of the purchase receipt.
Australia
Oricom International Pty Ltd
PO Box 5681, South Windsor, NSW 2756
Customer support
Email: support@oricom.com.au
Web: www.oricom.com.au
Fax: (02) 4572 0939
Ph: 1300 889 785
New Zealand
Atlas Gentech (NZ) Ltd
Private Bag 14927, Panmure, Auckland
Customer support
Email: support@atlasgentech.co.nz
Web: www.atlasgentech.co.nz
Fax: (09) 574 2722
Ph: 0900 50 025 (Toll Call)