Filter
Top Products
www.bbpglobal.com
Smart Internet Phone Adapter
TA612V
BBPGlobal
Add voice to your internet
INSTALLATION GUIDE
INSTALLATION WITH MULTIPLE DEVICES
This guide shows you how to set up your Smart Internet Phone Adaptor
with a Router or Switch instead of just a single PC. This way you can share
your internet connection with multiple computers (i.e. via Wireless Lan).
1. SET UP THE NETWORK CONNECTIONS
a. Unplug the power cable for your modem.
b. Unplug the power cable for your router.
c. Disconnect the Ethernet cable connectiong your modem to your
router from the WAN/Internet port on your router, and connect
that end of the Ethernet cable to the Internet port on the TA612V
Smart Internet Phone Adaptor.
d. Connect one end of the Ethernet cable we provide into the PC
port on the TA612V. Connect the other end of this Ethernet cable
into the WAN/Internet port on your router.
e. Plug the power cable back into your modem. Wait about two
minutes for it to start up.
2. THEN, INSTALL THE TA612V VOICE ADAPTER
a. Plug the power cable into the Power port on the TA612V Smart Internet
Phone Adaptor and into an electrical outlet. This turns on your Smart
Internet Phone Adaptor. You do not need to unplug it when not in use.
b.
Check that the Power light on the Smart Internet Phone Adaptor is
illuminated.
Wait at least five minutes for the phone adapter to start up.
There may be updates that need to be downloaded such as new firmware or
changes to your features. Do not interrupt the registration process by
unplugging the power or lifting the receiver on your phone during the
start-up process. Interruption of the startup may result in interruption
of service.
c. The status light on the front of the TA612V will flash. Wait two minutes
before continuing.
d. Plug the power cable back into your router and wait about two minutes for it
to start up before continuing.
e. Connect a telephone to the TA612V Phone 1 port using the adapter provided.
f. If you have a DSL modem that requires PPPoE you need to set up your PPPoE
username and password in the TA612V. Point your browser to:
http://192.168.61.1
/
Log in using the username and password printed on the back of the TA612V.
After setup reboot your TA612V.
12VDC, 1.2A
Power
Phone 2
(inactive)
Phone 1
Restore
Factory
Settings
PC
Internet
Power
Status
Internet
PC
Phone 1
Phone 2
Blink=Activity Ethernet: Green=100Mbps/Amber=10Mbps
BBPGlobal
Add voice to your internet
TROUBLESHOOTING
If you have no dial tone, check the following:
• Make sure the phone is plugged into the proper port on the Smart
Internet Phone Adaptor (phone port #1)
• Make sure the Internet light on the Smart Internet Phone
Adaptor is active. If not, check your connection to the Internet. Try
rebooting your modem. If that does not work, contact your internet
provider’s customer service.
The
easiest
way
to
get
VoIP
www.bbpglobal.com
3. SET UP AN ACCOUNT AT BBPGLOBAL
a) Power up the computer.
b) Use a Web browser to go to the bbpglobal web site,
http://www.bbpglobal.com/netgear/
Follow the instructions to setup your account. During this process,
you will be asked to provide your contact information, the serial
number and the MAC address of your TA612V, shown at the back
of your unit.
c) Reboot your TA612V after registration.
d) After reboot, pick up your telephone handset and listen for a dial
tone. If you hear dial tone then you have finished installation and
may begin making calls. For dialing instructions, see the Helpfule
Hints on this card. If you do not hear a dial tone, see
Troubleshooting. For more tips about troubleshooting, see the
User Manual.
e) (Optional) You may also select a PSTN number to receive phone
calls. Please go to the following web site to select a PSTN number.
Please note there is an additional charge for this service.
http://www.bbpglobal.com/phonenumber/