Kenwood TK-7150 Two-Way Radio User Manual


 
ADS#26608 Printed in USA
JQA-QMA1205
Specifications
Applicable MIL-STD & IP
Model TK-7150 TK-8150
GENERAL
Frequency Range
Type1: 136~174MHz 450~500MHz
Number of Channels (Zone)*
Conventional CH: Max.128 (1 zone x 128ch ~ 128 zones x 1ch)
Trunking ID: Max. 250/zone (max.32 zones)
Channel Spacing
Wide: 25kHz, 30kHz 25kHz
Narrow: 12.5kHz, 15kHz 12.5kHz
Operating Voltage 13.6V DC±15%
Current Drain
Standby: 0.5A 0.5A
Receive: 2.3A 2.3A
Transmit: Less than 12A Less than 13A
Duty Cycle Transmit: 20%
Operating Temperature Range -22ºF ~ +140ºF (-30ºC ~ +60ºC)
Frequency Stability ±0.00025%
(-22ºF ~ +140ºF)
Antenna Impedance 50
Dimensions (W x H x D) 7-1/12” x 2” x 7”
(180mm x 50mm x 170mm)
Weight (net) 5.9 lbs (2.7kg)
FCC ID ALH32273110 ALH32283110
Band Spread 38MHz 50MHz
Model TK-7150 TK-8150
RECEIVER
(Measurements made per EIA/TIA-603)
Sensitivity
12dB SINAD: 0.35µV
20dB Quieting: 0.45µV
Selectivity
Wide: 84dB (±30kHz) 80dB (±25kHz)
Narrow: 76dB (±15kHz), 73dB (±12.5kHz)
76dB (±12.5kHz)
Intermodulation
Wide: 77dB (±30, 60kHz) 79dB (±25, 50kHz)
Narrow: 75dB (±15, 30kHz) 73dB (±12.5, 25kHz)
Spurious Response 85dB
Audio Output
External: 12W (@ 4 3% distortion)
13W (@ 4 5% distortion)
Internal: 3.2W (@ 16 3% distortion)
3.5W (@ 16 5% distortion)
TRANSMITTER
(Measurements made per EIA/TIA-603)
RF Output Power 50 to 15 watts 45 to 15 watts
High: 50 watts 45 watts
Low: 15 watts 15 watts
Type of Emission
Wide: 16K0F3E, 20K0F1D
Narrow: 11K0F3E, 11K2F1D
Spurious Response 75dB
FM Hum & Noise
Wide: 48dB
Narrow: 42dB
Microphone Impedance 600
Audio Distortion Less than 1% at 1000Hz
KMC-9C
Desktop Microphone
KMC-27A
Microphone
(noise-canceling)
KMC-27B
Microphone
KMC-28A
Keypad Microphone
(noise-canceling)
KCT-18
Ignition Sense Cable
KCT-22
Remote Control Cable
8 feet
17 feet
25 feet
KCT-23
DC Power Cable
Medium Power
Dash (10 feet)
Medium Power Remote
(Positive: 23 feet,
Negative: 3.3 feet)
KES-5
External Speaker
KLF-2
Line Filter
KPS-10A
Regulated DC
Power Supply
KPS-15
DC Switching
Power Supply
KRK-9
Single Control Head
Remote Kit
Options
All accessories and options may not be available in all markets. Contact an authorized
Kenwood dealer for details and complete list of all accessories and options.
Standard MIL 810C MIL 810D MIL 810E MIL 810F
Methods/Procedures Methods/Procedures Methods/Procedures Methods/Procedures
Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II
High Temperature 501.1/Procedure I, II 501.2/Procedure I, II Cat. A1 501.3/Procedure I, II Cat. A1 501.4/Procedure I, II
Low Temperature 502.1/Procedure I 502.2/Procedure I, II Cat. C1 502.3/Procedure I, II Cat. C1 502.4/Procedure I, II
Temperature Shock 503.1/Procedure I 503.2/Procedure I Cat. A1, C1 503.3/Procedure I Cat. A1, C1 503.4/Procedure I, II
Solar Radiation 505.1/Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I
Rain 506.1/Procedure II 506.2/Procedure II 506.3/Procedure II 506.4/Procedure III
Humidity 507.1/Procedure II 507.2/Procedure II 507.3/Procedure II 507.4
Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4
Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III
Vibration 514.2/Procedure VIII, X 514.3/Procedure I Cat. 8 514.4/Procedure I Cat. 8 514.5/Procedure I Cat. 20
Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V
Kenwood follows a policy of continuous advancement in development.
For this reason specifications may be changed without notice.
* During simultaneous operation of conventional and LTR
®
modes.
Conventional channel/trunking ID can be programmed up to 512.
footnotes from Front:
1
KRK-9, KCT-22M/M2/M3, KCT-23M/M3
remote control options required.
2
6-Pin Accessory Connector for external
speaker, PA Output & ignition sense input.
3
KCT-18 ignition sense cable option required;
plugs into mobile 6-pin jack ignition sense input.
4
Built-in PA/HA outputs (no option board
required); Horn Alert operates for 2-Tone or
DTMF selective call decode only.
5
Short Text Messages are radio stored & LCD
displayed; Long Text Messages require a
KDS-100 and KCT-40.
6
FleetSync
®
GPS features require an internal
GPS board or externally wired GPS receiver
with NMEA TTL level serial data output to
the internal COM 1 or 2 set to "GPS".
FleetSync
®
is a trademark of Kenwood Corporation.
LTR
®
is a registered trademark of Transcrypt International.