Extron electronic IPI 201 Intercom System User Manual


  Open as PDF
of 2
 
IPI 200 Series Setup Guide (Continued)
68-1170-51
Rev B
06 10
Installation
Before installing your IPI 200, read the following publications, which can be found on the Extron Web site (www.extron.
com):
• IPI 100 Series and IPI 200 Series User’s Manual
• IP Intercom System Frequently Asked Questions
CAUTION: Installation and service must be performed by authorized personnel only. These products must be used with
UL approved grounded electrical boxes.
PUSH TO CALL
Speaker Microphone On LED
Microphone
Push To Call ButtonsConfig Port
Extron IPI 204 AAP Intercom (front panel)
POWER RELAY
C NO
AUDIO OUT
LAN
Power
Contact
Relay
Audio Out
IPI 204 AAP, IPI 201 AAP (rear panel)
LAN Port
AAP Mounting
Screws (4)
The front panel of the IPI 204 is shown above, at left. The front panel for the IPI 201 is similar but has only one button. The
rear panels for both units are identical and are shown above, at right.
1. Determine which rooms will have IP Intercoms and HelpDesk PCs, and where in each room they will be located. Ensure
there is a network connection for each intercom and each HelpDesk PC.
2. Connect the LAN port to the local network, using a standard network cable, with an RJ-45 connector.
3. Connect power, and, if required, contact relay and local audio output, using the rear panel
captive screw connectors (see figure at right).
4. Test the equipment is working correctly before installing in the wall.
5. Mount each IPI 200 into furniture, an AAP wallplate, mounting bracket for 2-gang
wallplates, or device faceplate. The AAP versions must be secured by attaching a clamp
bracket to the back of the intercom after it has been inserted through the front of the AAP plate.
6. Ensure the HelpDesk PC(s) is connected to the network and power it on.
7. Install the Extron IP Intercom HelpDesk software from the disk supplied. It is also available for download from the
Extron Web site (
www.extron.com)
8. Use the IP Intercom HelpDesk software to configure parameters such as speaker level for all intercom units in the
system. Full instructions can be found in the IPI 100 Series and IPI 200 Series User’s Manual and also in the help file for
the software.
When the front panel button(s) light a low amber color, the unit is correctly installed and configured. If the button(s) light
red the unit is not correctly configured and you should check the IPI 100 Series and IPI 200 Series User’s Manual or the help
file for the software.
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.833.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2010 Extron Electronics. All Rights Reserved. www.extron.com
POWER RELAY
C NO
AUDIO OUT
 previous