Filter
Top Products
Setting up
Inside this package you will find:
• Casio DC5001 handset and belt clip.
• Charging Cradle.
• Power adaptor with cable attached.
• Users guide for the CASIO DC5000.
Installation
1. Install the rechargeable batteries (supplied)
into the handset. Slide open the cover and
insert as indicated on the label inside the
battery compartment, then refit the cover.
2. Decide where you will locate the charging
cradle.
You can choose to place your charging cradle
on a desk or attach it to a wall, whichever is
the more convenient. Make sure the charging
cradle is not placed in direct sunlight, or in a
room with high humidity. It is also important to
ensure that the cradle is located within range
of the base station.
I.E. in a location from where you can make
calls from your existing handset.
Try not to place your charging cradle too close
to existing electronic equipment (such as a
phone, fax, answering machine, computer, TV
and radio) as this may impair performance of
the equipment. We recommend a distance of
at least one metre.
3. Connect the power adaptor cable plug to the
charging cradle.
Use only the power adaptor — supplied with
your charging cradle.
4. Fit the adaptor cable into the groove.
5. Slide the adaptor cable under the groove and
gently tighten the loop.
6. Plug the mains power adaptor into a (230V)
mains socket and switch it on.
7. Place the handset into the charging cradle
with the keypad facing towards the front. The
charging light will come ON.
8. Charge the batteries for at least 16 hours. (16
hours charge time is required for the first
charge, subsequent charges will take around
4 to 5 hours.)
9. Register the handset on to the Casio DC5000
base station.
• Press and hold down PAGE (on the base) for
longer than 5 seconds. The base will start to
beep.
• Press PROG on the handset to be registered.
• Press the 8 button.
• Select a base station number shown on the
display 1-4. If you only have 1 base station,
this should be 1.
• Enter the 4-digit sys code (this will be the
factory setting of 0000 unless you have
changed this on your base unit).
• Press PROG. The handset will now register
with the base and the display will show the
available handset numbers.
• Select a number to be used for the handset
from those shown on the display.
If you have problems with the installation of the
cradle or registration of the handset, please call
the helpline during office hours on 01438 749009.
Wall mounting the charging
cradle
1. Before mounting the charging cradle on a
wall, ensure that the handset is within range
of your base station, when located in your
chosen wall mounted position.
a) Follow the instructions given above,
including the charging of the handset
batteries and registering the handset on
the base station.
b) Press the PAGE button on the base unit
and within 30 seconds, hold the handset
temporarily in your chosen location and
ensure that it rings.
c) When you are confident that the handset
is within range of the base when located in
your chosen position, disconnect the
adaptor plug from the mains wall socket
and proceed as follows.
2. Secure the cradle to the wall using Brass
round head size 10 screws, 1 1/4" in length
(30mm).
The screws should be fitted 35mm apart.
IMPORTANT — Before drilling the wall, check that
there are no pipes or cables buried in the wall,
that will be damaged by the drill. Do not drill
directly above or below other electrical fittings
unless you are sure that the cables to these are
routed away from the drill position.
3. Mount the charging cradle on the screws.
4. Put your handset back in the charging cradle
and switch the power on at the wall socket.
The charging light should come on.
IMPORTANT — The batteries supplied with this
product are rechargeable Ni-MH, 1300mAh.
When replacing batteries, never use other types of
batteries or conventional alkaline batteries.
35mm
SCREW
Charging
compartment
Charging
indicator
DC5001 5/10/99, 12:09pm2