Filter
Top Products
For there will be additional handset, charge cradle,
belt clip, battery pack and cover than shown above.
For there will be additional handsets, charge cradles,
belt clips, battery packs and covers than shown above.
For there will be additional handsets, charge
cradles, belt clips, battery packs and covers than shown above.
This product meets the applicable Industry Canada technical specications.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference
that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certied equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe systems, if present,
are connected together. This precaution may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
This equipment may not be used on coin service provided by the telephone
company.
This equipment generates and uses radio frequency energy which may interfere
with residential radio and television reception if not properly installed and used in
accordance with instructions contained in this manual. Reasonable protection against
such interference is ensured, although there is no guarantee this will not occur in a
given installation. If interference is suspected and veried by switching this equipment
on and off, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient the radio/television receiver’s antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into separate
circuit outlets. The user may also wish to consult a qualied radio/television technician
for additional suggestions. This equipment has been fully tested and complies with all
limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
1. Turn the base over.
2. Attach the wall mounting pedestal by rst inserting the tabs on the open
edge of the pedestal into the slots on the lower portion of the bottom of
the base. Then push down and snap the pedestal into place.
3. Slip the mounting holes (on the back of the base) over the wall plate posts,
and slide the unit down into place. (Wall plate not included.)
This section shows you how to set up your answering system to receive
incoming calls. Before you begin the set up process, you must turn on the
answering system.
• Press the ans on/off button to turn the answering system and .
The MESSAGES indicator lights when the answering system is . The
indicator blinks when you have new messages.
The default voice prompt language is English.
To change the answering system’s voice prompt language, press and hold
the skip button for two seconds. The unit announces
(Spanish selected).
1. Make sure the answering system is .
2. Press and hold the day/check button on the base to set the day of the
week.
3. Press and hold the hour button on the base to set the hour (a.m. or p.m.).
Example: or.
4. Press and hold the min button on the base to set the minute. The time
advances in 5-minute intervals, or tap and release to advance in 1 minute
intervals.
For best results when recording, you should be about nine inches from the
microphone, and eliminate as much background noise as possible.
1. Make sure the answering system is .
2. Press and hold the announce button on the base.
3. Begin speaking after you hear the beep.
4. Release the button when you nish your announcement.
Press and release the announce button to review your outgoing
announcement.
Use the RINGS TO ANSWER switch on the back of the base to set the number
of times you want the phone to ring before the answering system answers
the call. You may choose 3 rings, 5 rings, or TOLL SAVER (TS).
There are nine programmable menus available: Language, Handset Name,
Area Code, Ringer ON/OFF, Ringer Tone, VIP Ring Tone, Tone/Pulse, Transfer
and Default Setting.
During programming, you may press the mute/menu button at any time to
go to the next option. Pressing mute/menu button takes you through the
menu choices. When changes have been made to selected menu item,
pressing the mute/menu button saves the changes and Conrmation Tone
sounds. To exit the menu and keep the previous setting and return to the
standby mode, press the *EXIT/tone button.
1. Press the mute/menu button until 4 shows in the
display. 1ENG is the default. (ENG stands for English. FRA stands for
French. ESP stands for Spanish.)
2. Use the
CALLER ID-VOLUME5
or
6
button or the touch-tone pad on
the handset to enter your selection.
3. Press mute/menu again to save.
1. Press the mute/menu button until shows in the display.
2. Use the touch-tone pad to enter the name (up to 15 characters). More
than one letter is stored in each of the number keys. For example, to
enter the name Bill Smith, press the 2 key twice for the letter B. Press
the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter
L. Wait for one second. Press the 5 key 3 times for the second letter L.
Press th e 1 key to insert a space between the L and the S. Press the 7
key 4 times for the letter S; press the 6 key once for the letter M; press
the 4 key 3 times for the letter I; press the 8 key for the letter T; press
the 4 key twice for the letter H.
3. Press mute/menu again to save.
This program setup allow you to setup how the incoming caller ID show on
the display.
1. Press the mute/menu button until shows in the
display. “- - -” is the default.
2. Use the touch-tone pad on the handset to enter your three digit area code.
3. Press mute/menu again to save.
1. Press the mute/menu button until 4shows in the
display. 1ON is the default.
2. Use the
CALLER ID-VOLUME5
or
6
button or the touch-tone pad on the
handset to scroll to or .
3. Press mute/menu to save.
You can choose from 10 ringtones.
1. Press the mute/menu button until 4 shows in the
display. 01 is the default.
2. Use the
CALLER ID-VOLUME5
or
6
button or the touch-tone pad on the
handset to select from to .
3. Press mute/menu to save.
This feature allows you to assign a specic ring tone to a number stored in
Memory. It is recommended that you store a Caller ID record into Memory
for this purpose.
1. Press the mute/menu button until shows in the display.
2. Press the desired memory location (0 through 9). If there is a number
stored in the selected memory location, 4 shows in the
display.
3. Press
CALLER ID-VOLUME5
or
6
on the handset to select from
or to use ring tone set in the Ringer Tone Menu or to
silence ringer.
4. Press mute/menu to save.
1. Press the mute/menu button until 4 shows in the
display. 1 TONE is the default.
2. Use the
CALLER ID-VOLUME5
or
6
button or the touch-tone pad on
the handset to scroll to or .
3. Press mute/menu to save.
In order to use the Call Transfer feature (applicable ONLY with additional
handsets), you must have the Transfer ON/OFF set to ON through the menu
of the transferring handset.
1. Press the mute/menu button until 4 shows in the display.
2. Use the CALLER ID-VOLUME (
5
or
6
) button or the touch tone pad on the
handset and select .
3. Press mute/menu again to save.
You may return handset settings to the factory default setup using this
menu.
1. Press the mute/menu button until 4 shows in the display.
NO is the default.
2. Use the CALLER ID-VOLUME (
5
or
6
) button on the handset to scroll to
or .
3. Press mute/menu to save.
The phone is when the charge/in use indicator on the base is lit. The handset
visual ringer and base indicator ash when you receive a call.
1. When the phone rings, pick up the handset and press the TALK/CALL BACK
or SPEAKER button.
2. When nished, press the TALK/CALL BACK or SPEAKER button again or
place the handset on the base cradle to hang up.
1. Pick up the handset and press the TALK/CALL BACK or SPEAKER button.
Wait for the dial tone. The call timer starts counting minutes and seconds
in the display.
2. Dial a telephone number.
3. When nished, press the TALK/CALL BACK or SPEAKER button again or
place the handset on the base cradle to hang up.
1. Make sure the phone is (not in TALK mode).
2. Dial a telephone number (the number you dial shows in the display).
3. Press the TALK/CALL BACK or SPEAKER button on that handset. The
number automatically dials and the call timer starts counting the minutes
and seconds in the display.
4. When nished, press the TALK/CALL BACK or SPEAKER button again to
hang up.
While the phone is (in TALK or SPEAKERPHONE mode), press the redial
button to redial the last number you dialed (up to 32 digits).
- OR -
While the phone is (in standby mode), press the redial button and then
the TALK/CALL BACK or SPEAKER button to redial the last number.
Use the ash/answerer/call waiting button to activate custom calling
services such as call waiting, which are available through your local phone
company.
While talking on the phone, it may be necessary for you to manually change
the channel to improve reception and reduce noise or static on the line. Press
and release the chan/delete button to move to the next clear channel.
Model 25952
00017256 (Rev. 1 Can E/F)
07-40
Printed in China
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a modular
jack, call your local phone company to nd out how to
get one installed.
Your cordless phone uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
• Avoid sources of noise and heat, such as motors, uorescent lighting,
microwave ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Press the *EXIT/tone button to cancel any command you initiated.
This feature assists in locating a misplaced handset.
Press the page button on the base. The handset beeps continuously for
about 2 minutes until you press the TALK/CALL BACK or SPEAKER button on
the handset or the page button on the base.
This feature allows you to turn off handset ringers for all handsets
registered with the base unit. The answerer speaker will be silenced
when the unit is receiving incoming messages.
Press the
do not disturb
button on the base. Handset will display
.
Apart from the setting in the main menu, there is a shortcut to set the ringer.
Make sure the phone is (not in talk mode).
1. Press the #PAUSE/ringer button to go to the menu.
4 shows in the display. 1ON is the default.
2. Use the CALLER ID-VOLUME (
5
or
6
) button or the touch-tone pad on the
handset to scroll to or .
3. Press the #PAUSE/ringer button to save your selection. You will hear a
conrmation tone.
When the phone is (in TALK or SPEAKERPHONE mode) press the CALLER
ID-VOLUME (
5
or
6
) button to adjust the listening level. Choose from ve
volume settings. is the lowest volume and is the highest volume.
Use mute during a phone conversation to speak privately and off-line with a
third party.
1. Press the mute/menu button. shows in the display. The party on the
telephone will not hear you.
2. Press the mute/menu button when nished.
1. If you are using the handset earpiece and want to switch to the
speakerphone, press the SPEAKER button, you can then press SPEAKER
button again to end conversation.
2. If you are using the speakerphone and want to switch to the handset
earpiece, press the TALK/CALL BACK button, you can then press the TALK/
CALL BACK button again to end conversation.
This feature is useful only if you have pulse (rotary) service. Temporary Tone
Dialing enables pulse (rotary) service phone users to access touch tone
services offered by banks, credit card companies, etc. For example, when
you call your bank you may need to enter your bank account number.
Temporarily switching to touch tone mode allows you to send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the *EXIT/tone button on the handset to
temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse
(rotary) dialing mode.
During an external call, you may transfer the external call to another
handset.
1. Press the format/trans button on the originating handset.
shows in the display. All registered handsets will be paged.
2. Press the format/trans button or TALK/CALL BACK on receiving handset to
answer call.
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company, where practicable, may notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business. If these changes are expected to affect the use or performance of your
telephone equipment, the telephone company will likely give you adequate notice to
allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone
from your line.
On the bottom of this equipment is a label indicating, among other information, the
Ringer Equivalence Number (REN) for the equipment.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
line should not exceed 5. To be certain of the number of devices you may connect to
your line as determined by the REN, you should contact your local telephone company.
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,427,009.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
Make sure your package includes the items shown here.
1. Locate battery and battery door which are packaged together inside a
plastic bag and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
shows in the display.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into
place.
1. Choose an area near an electrical outlet and a telephone wall jack
(RJ11C), and place your cordless telephone on a level surface, such as a
desktop or tabletop, or you may mount it on the wall.
2. Plug one end of the telephone line cord into the TEL LINE jack at the back
of the base and the other end into a modular jack.
3. Plug the AC power converter into the electrical outlet and the DC
connector into the jack at the back of the base.
4. Place the handset in the base cradle. The charge/in use indicator turns on,
verifying the battery is charging. The unit will take 20 seconds to register
and verify its security code. shows in the display.
5. Allow the phone to charge for 16 hours prior to rst use. If you don’t
properly charge the phone, battery performance is compromised.
6
5
8
7
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
This unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date, and time; or
the name, phone number, date, and time.
Provided you subscribe to Call Waiting Caller ID service from your phone
company; if you receive an incoming call and you are already on the phone,
a beep indicates the presence of a Call Waiting call on the line. Only the
handset that is in use at the time of the call will display and store the Call
Waiting Caller ID information.
• When you hear the call waiting beep in the handset receiver, press the
ash/answerer/call waiting button to put the current call on hold and
answer the incoming call. Press ash/answerer/call waiting again to return
to the original call.
When you receive a call, the Caller ID information is transmitted between the
rst and second ring. The Caller ID information appears on the display while
the phone rings, giving you a chance to monitor the information and decide
whether or not to answer the call.
If you are not at home or cannot answer, your telephone’s Caller ID memory
stores the data for the 40 most recent calls you received so you can see who
called while you were unavailable. When the 41st call is received, the oldest
Caller ID record (1st call) is automatically deleted.
You may review the stored information at any time. Calls received since your
last review show as in the display. Calls that have not been previously
reviewed but were received from the same number more than once show as
in the display.
As calls are received and stored, the display is updated to let you know how
many calls have been received. To scroll CID records:
1. Make sure the phone is (not in talk mode).
2. Press the CALLER ID-VOLUME (
6
) button to review the newest CID record.
3. Press the CALLER ID-VOLUME (
5
) button to review the oldest CID record
rst.
1. Make sure the phone is (not in TALK mode).
2. Use the CALLER ID-VOLUME (
5
or
6
) button to display the desired record.
3. Press the TALK/CALL BACK or SPEAKER button. The number dials
automatically.
Available formats include:
Number of digits Explanation Example
long distance code “1 ” 1-317-555-8888
+3-digit area code
+7-digit telephone number.
3-digit area code + 317-555-8888
7-digit telephone number.
7-digit telephone number. 555-8888
30 Eglinton Ave W., Suite 304
Mississauga, ON Canada L5R 3E7
© 2007 Thomson Digital Technologies Ltd.
Trademark(s) ® Registered
Marque(s) ® déposée(s)