GE 29581 Telephone User Manual


 

Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID
records and for storing the numbers you use for memory dialing, pulse dialing, and redial.







1. If the telephone line cord is connected, disconnect it
from the base unit.
2. Release latch on battery compartments and remove
cover.
3. Insert 4 AA-size alkaline batteries as shown on the
diagram in the battery compartments.
4. Snap the battery compartment doors back into place
and replace the mounting bracket.
5. If the line cord was previously connected, re-attach it
to the unit and check your memory locations.




Your phone should be placed on a level surface, such as a desk or table top, or you can
mount it on a wall. A wall mounting pedestal is packaged with your phone.

1. Connect one end of the coiled handset cord to the jack on the handset.
2. Plug the other end of the coiled handset cord to the jack on the base.
3. Place the handset in the cradle.

1.
Connect one end of the straight telephone line cord to the jack on the back of the base.
2. Connect the other end to a wall phone
jack.
3.
Set the ringer volume switch located
at the back of the base to the desired
loudness.
OFF - Telephone will not ring.
LO - Sound will be lowest.
HI - Sound will be loudest.



Your speakerphone can also be mounted on a wall plate (not included).





Rotate the hook 180°. (Refer to Dia. 1A)
Turn the phone over so that the bottom of the base is facing
up and the thickest end is pointing away from you.
• If desired gather the extra telephone line cord together and
store inside the wall mounting pedestal, and then thread the
line cord through the grooves on the pedestal according to
the illustration.
With the rounded end of the pedestal pointing upward, insert
the tab on the end of the pedestal into the middle slot on the
bottom of the base, then push the pedestal down
until the two tabs on the left and right corners of
the pedestal snap (lock) into the two lower slots on
the bottom of the base.
Slip the mounting holes over the wall plate posts
and rmly slide the unit down into place (wall plate
not included).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
“receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and
receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which
the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced
radio/television technician for additional suggestions. Also, the Federal Communications Commission
has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This
booklet is available from the U.S. Government Printing Ofce, Washington, D.C. 20402. Please specify
stock number 004-000-00345-4 when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

This telephone system meets FCC standards for Hearing Aid Compatibility.

Licensed under US Patent 6,427,009.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.

This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.
1. Press the  button until TONE/PULSE MODE shows in the display.
2. Press the 3 or 4buttons to show the current dialing mode. The default is TONE
dialing.
3. To change the dialing mode, press the 3 or 4 buttons. The display alternates
between the two modes.
4. Press the  button again to save.





You may store information in any of the following memory locations: 0 to 9, A, B, and C .
See “Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.

1. Press the  button. LOCATION? shows in the display.
2. Press the desired memory location (0-9, A, B, C).
34 

3. Press the  button again to conrm the memory location.


4. Use the number keys to enter the telephone number (up to 32 digits) and press the
 button to save. (The unit will not dial a phone number in this mode.) The cursor
automatically moves to the text line for name entry.
5. Use the number keys to enter the name of the person associated with the telephone
number you just entered. More than one letter is stored in each of the number keys.
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B.
Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.

34 

Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to
insert a space, and press the 7 key 4 times for the letter S. Press the 6 key once for
the letter M. Press the 4 key 3 times for the letter I. Press the 8 key for the letter T.
Press the 4 key twice for the letter H.
6. Press the  button to save the name.
7. To enter another name and number in a different memory location, return to step 1
and repeat the process.

Repeat the storage sequence under “Storing A Name and Number in Memory”, and use
the  button to delete the old number before entering the new number.

1. Press the  button.
2. Press the memory location (0-9, A, B, C) to be erased.
3. Press the  button.

1. Press the 3 or 4 buttons to view the caller number and name you want to copy.
2. Press the  button.
3. Press the memory location (0-9, A, B, C). The number ashes if there is a number
already stored in the memory location.
4. Press the  button to enter the edit mode, and then press the  button again
to edit the name.
34

5. Press the  button to conrm and save, and wait for three seconds to exit.



1. Press the  button.
2. Press any key (0-9, or quick call buttons A, B, or C) for the memory location. If there
is a number already stored in the memory location it will appear on the display. Use
the 
3 or 4
button to select a different location.
3. Press the  button again to conrm.
4. Press the  button, and then press the  button again.
5. Enter name, if necessary, and then press the  button to conrm.




1. Press the  button.
2. To select a memory, press any number key (0-9, A, B, C). The number in that memory
location displays.
34

3. Press the  button, or pick up the handset to dial the displayed number.

1. Lift the handset, or press the  button.
2. Press the  button then press a memory location button.


Your telephone equipment is approved for connection to the Public Switched Telephone Network
and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical
Requirements for Telephone Terminal Equipment published by ACTA.
 
On the bottom of this equipment is a label indicating, among other information, the US number
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line
and still have all of these devices ring when your telephone number is called. In most (but not
all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be
certain of the number of devices you may connect to your line as determined by the REN, you
should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
details.

• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own
telephone equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this product does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualied installer.


 
Should your equipment cause trouble on your line which may harm the telephone network,
the telephone company shall, where practicable, notify you that temporary discontinuance of
service may be required. Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue service immediately. In case
of such temporary discontinuance, the telephone company must: (1) promptly notify you of
such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3)
inform you of your right to bring a complaint to the Commission pursuant to procedures set
forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and not
inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or
performance of your telephone equipment, the telephone company must give you adequate
notice, in writing, to allow you to maintain uninterrupted service.

You can use the telephone by speaking into and listening through the handset, or by
using the speakerphone.

1. Lift the handset or press  to answer the call.
2. Replace the handset in the cradle or press the  button to hang up.

1. Lift the handset or press the  button. Wait for a dial tone.
2. Dial the telephone number you want to call.
3. Replace the handset in the cradle, or press the  button to hang up.

You may adjust the handset and speakerphone volume independently with the 
button or the ( or ) buttons. Both handset receiver volume level and speakerphone
volume level are saved in memory.

While using the handset, you can adjust the speaker volume by pressing the 
button continuously or pressing the ( or ) buttons after pressing the  button.
REC (Handset Receiver) volume shows in the display.

While using the speakerphone, you can adjust the speaker volume by pressing the 
button continuously or pressing the ( or ) buttons after pressing the  button.
SPK volume level shows in the display.



You may redial the last number you called by pressing the  button after you hear
a dial tone.





Use the  button to interrupt a phone conversation to talk privately with someone
else in the room. A conversation can be muted while using the speakerphone or
handset.
1. Press the  button. The mute indicator illuminates.
2. Press  again to turn it off.


Press  to activate special features of your telephone network, such as call
transfer, or special services from your local telephone company, such as call waiting.

If you have pulse (rotary) service and want to access customer calling services (such
as telebanking and long distance services) that require tone dialing, you can use this
feature to temporarily change from pulse to tone service.
After dialing the telephone number and connecting to the customer calling service,
1. Press and release the  button.
2. When you hang up, the telephone automatically returns to pulse dialing mode.


Your phone features a speakerphone for ease of use and convenience during a phone
conversation. At any time during a conversation, you can lift the handset to stop using
the speakerphone. Likewise, when you are using the handset, press the  button
and place the handset in the cradle to switch to the speakerphone.
For best speakerphone performance, avoid the following:
Areas with high background noise. (The microphone might pick up these sounds and
prevent the speakerphone from going into the receiving mode when you nish talking.)
Surfaces affected by vibration.
Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which
can generate an echo effect.

Note the following guidelines when using the speakerphone:
The speakerphone works similar to a two-way radio in that you can only listen or talk
at one time.
Stay reasonably close to the phone so that you can be clearly heard by the person to
whom you are talking.
You can adjust the speaker volume by pressing the  button continuously or
pressing the  button3 or 4after pressing the  button.
The speakerphone indicator light comes on when the speakerphone is in use.








The Summary Screen shows the current time, date, and number of new calls to review.
It is displayed until any button is pressed.



This process allows you to dial a succession of stored numbers from separate memory
locations. This is useful when you must dial several sequences of numbers, such as with
frequent calls via a telephone company long distance provider.
For example Memory location
Local access number of long distance company 6
Authorization code (ID) 7
Long distance phone number 8
1. Pick up the handset or press .
2. Press  button, then press number “6” for the memory location.
3. Press  button, then press number “7” for the memory location.
4. Press  button, then press number “8” for the memory location.
5. The number dials automatically.

The  button has dual functionality and becomes a  button when the 
button is pressed rst. It is valid only when storing a number into memory locations.
Use the button to insert a pause when a delay is needed in an automatic
dialing sequence. For example, when you must dial a 9 to get an outside line or when
you enter codes to access your long distance company.

1. With the handset on the cradle, enter the telephone number you wish to call. The
telephone number shows in the display.
2. Lift the handset or press the  button and the number automatically dials.


The following special messages indicate the status of a message or the unit:
 The caller of the incoming call is registered as
“Private Number” and their Caller ID information is withheld.
 Indicates a call is waiting on the line.
Battery power level is low.
 The caller memory is empty.
 You are at the beginning or the end of the Caller ID memory log.
 The incoming call does not have Caller ID service or their service
area is not linked to yours. If UNKNOWN CALLER appears along
with a calling number, the name information for that number was
not available.

No Dial Tone
Check all cabling to make sure that all connections are secure and not damaged.
Check hook switch: Does it fully extend when handset is lifted from cradle?
No Display
Replace the batteries.
Check for proper battery installation.
No Information is Shown After the Phone Rings
Are you subscribed to Caller ID service from your local telephone company?
Be sure to wait until the second ring before answering.
Phone Dials in Pulse with Tone Service
• Make sure T/P DIAL MODE is set to TONE DIAL.
Phone Won’t Dial Out with Pulse Service
• Make sure T/P DIAL MODE is set to PULSE DIAL.
Phone Does Not Ring
Make sure ringer switch is set toor.
You may have too many extension phones on your line. Try unplugging some
extension phones.
Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
• Are other phones off hook at same time? If so, this is normal condition as volume
drops when additional phones are used at once.
Check the handset receiver or speaker volume.
Memory Dialing
Make sure you entered the numbers correctly into memory.

To keep your phone working and looking good, follow these guidelines:
Avoid putting it near heating appliances and devices that generate electrical noise
(for example, motors or uorescent lamps).
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment to the unit.
Clean with a soft cloth.
Never use a strong cleaning agent or abrasive powder because this will damage the
nish.
Retain the original packaging in case you need to ship it at a later date.

This units receives and displays information transmitted by your local company.
This information can include the phone number,date, and time ;or the name , phone
number, date, and time. The unit can store up to 75 calls for later review. When the
memory is full, a new call automatically replaces the oldest call in memory. NEW
appears in the display for calls received that have not been reviewed. REPT appears in
the display for calls received more than once which have not been reviewed.

• Press the 3 or 4 buttons to view the call records.
• Press the 6 button to scroll through the call records from the most recent to the
oldest.
• Press the 5 button to scroll through the call records from the oldest to the newest.
• When all of the records have been viewed, START/END appears in the display.

To delete the record shown in the display, press the  button once.
To delete all records while reviewing, press and hold the  button for about
three seconds. DELETE ALL? appears in the display. Press  again to complete.

When reviewing Caller ID records, you can dialback the numbers on the display by
pressing the  button.
PICKUP PHONE





1. Use the 3 or 4 buttons to display the number you want to dial.
2. Press the  button.
If you see a number with seven digits (i.e. 555-1234), then the call is from within your
area code. However, this does not guarantee the call is a local call.
If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from
within your area code.



3. If you are at on-hook and PICKUP OR ADJ displays, you can adjust the phone
number format by pressing the  button. If the phone is off-hook and ADJUST
shows in the display, you can adjust the phone number format by pressing the 
button. For example, sometimes a 7-digit local number cannot be dialed because
it requires a 10-digit or 11-digit format. Press the  button repeatedly to scroll
through the 7, 10, and 11-digit numbers.
 7-digit telephone number (i.e. 555-5555)
 3-digit area code + 7-digit telephone number (i.e. 425-555-5555)
 long distance code 1 + 3-digit area code + 7-digit telephone
number (i.e. 1-425-555-5555)
4. To dial the displayed number, and the phone is on-hook, pick up the handset or press
the  button before the timer reaches 0. If the phone is off-hook, wait until the
time reaches 0.NOW DIALING shows in the display and the number is dialed.

1. Use the 3 or 4 buttons to display the number you want to dial. You will only see
10-digit numbers (i.e. 234- 555-1234).
2. See steps 2 through 4 in the previous section to complete the dialback process.

You should not plug the telephone into the modular jack while setting up the Caller ID
menu.
1. Press the  button to enter the menu feature conguration mode.
# 1.  (CID language default English)
# 2.  (default level is 3)
# 3. 
# 4.  (Default is tone dialing).
2. Press the  button to scroll through the 4 menu screens.
3. Use the 3 or 4 buttons to select the desired setting.



This adjustment allows you to display the Caller ID prompts in English, French, or
Spanish.
1. Press the  button until ENG FRA ESP shows in the display.
2. Use the 3 or 4 buttons to select ENG, FRA or ESP.
3. Press the  button again to save.

This adjustment allows you to adjust the contrast of the display.
1. Press the  button until CONTRAST shows in the display.
2. Use the 3 or 4 buttons to select level 1, 2, 3, 4, or 5.
3. Press the  button again to save.

The telephone uses the programmed area codes to determine the number format to
display when a valid Caller ID signal is received. Numbers that match the local area
code are displayed as seven digits and are used for dialing back previous numbers.
Entering your local area code will also help you immediately know if the call is local or
long distance when viewing the CID records in the display.


1. Press the  button until LOCAL AREA CODE shows in the display.
2. Use the number keys to enter the Local Area Code you want.
3. Press the  button to save.
Model 29581
00021039 (Rev 0 Dom E/S)
08-02
Printed in China

101 West 103rd St.
Indianapolis, IN 46290-1102
© 2007 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)





SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:










If trouble is experienced with this equipment, for warranty information, please
contact customer service at . If the equipment is causing harm to
the telephone network, the telephone company may require that you disconnect the
equipment until the problem is resolved.
Any unauthorized repairs, changes or modications not expressly approved by
Thomson Inc. could void the user’s authority to operate this product. For instructions
on how to obtain a replacement unit, refer to the warranty included in this guide or call
customer service at .
Or refer inquiries to:




Attach your sales receipt to this booklet for future reference or jot down the date this
product was purchased or received as a gift. This information will be valuable if service
should be required during the warranty period.
Purchase Date
Name of Store


• Defects in materials or workmanship.

• One year, from date of purchase.
(The warranty period for rental units begins with the rst rental or 45 days from date
of shipment to the rental rm, whichever comes rst.)

• Provide you with a new unit. The exchange unit is under warranty for the remainder
of the original product’s warranty period.

• Properly pack your unit. Include any cables, etc., which were originally provided with
the product. We recommend using the original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the product is within the warranty period, must be presented to obtain warranty
service.” For rental rms, proof of rst rental is also required. Also print your name
and address and a description of the defect. Send via standard UPS or its equivalent
to:



• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of
damage or loss.
• A new unit will be shipped to you freight prepaid.
does not
• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. Any additional information, should be
obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modied or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.

• Please complete and mail the Product Registration Card packed with your unit. It will
make it easier to contact you should it ever be necessary. The return of the card is
not required for warranty coverage.

 





 









• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above
limitations or exclusions may not apply to you.
• This warranty gives you specic legal rights, and you also may have other rights that
vary from state to state.

• This warranty does not apply. Contact your dealer for warranty information.











 The part of the phone that pops up to activate the phone line when the
handset is lifted from the base.
 A term used to describe the phone in its active mode when the handset is off
of the base cradle or when the  button is pressed.
 A term used to describe the phone in an inactive mode.


Make sure your package includes the following items:

To use this phone, you need an RJ11C type modular telephone jack,
which might look like the one pictured here, installed in your home.
If you don’t have a modular jack, call your local phone company to
nd out how to get one installed.



Never install telephone wiring during a lightning storm.
Never touch uninsulated telephone wires or terminals, unless the telephone line has
been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
• Never install telephone jacks in wet locations unless the jack is specically designed
for wet locations.
• Temporarily disconnect any equipment connected to the phone, such as faxes, other
phones, or modems.



























