GE 27903 Cordless Telephone User Manual


 
4. Insert the battery pack.
5. Close the battery compartment by placing the handset back cover slightly
higher than the handset and then sliding the cover down into position.
Base Station
1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C),
and place your cordless telephone on a level surface, such as a desktop or
tabletop, or you may mount it on the wall.
2. Plug one end of the telephone line cord into the TEL LINE jack on the back of
the base and the other end into a modular jack.
3. Plug the AC power adaptor into the electrical outlet and the DC connector
into the jack on the back of the base.
4. Place the handset in the base cradle. The charge/in use indicator turns on,
verifying the battery is charging.
5. Allow the phone to charge for 16 hours prior to first use. If you don’t properly
charge the phone, battery performance is compromised.
CAUTION: Use only the
Thomson Inc. 5-2735
power adaptor
that came with this unit. Using other power adaptors may
damage the unit.
Wall Mounting
1. Rotate the handset hook up with a coin,
2. Insert the wall mount bracket into the socket at the front side of the unit.
(To uninstall the wall mount bracket, turn over the base, press and hold the
button on the bottom of the base and pull out the bracket at the same time.)
Press and hold
the button
Pull out the bracket
EquipmEnt ApprovAl informAtion
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the
US number and Ringer Equivalence Number (REN) for the equipment. You must, upon
request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
line should not exceed 5. To be certain of the number of devices you may connect
to your line as determined by the REN, you should contact your local telephone
company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone
company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.
• Notice must be given to the telephone company upon permanent disconnection of
your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
Thomson Inc.
10330 North Meridian Street
Indianapolis, IN 46290-1024
© 2006 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Model 27903
00016599 (Rev. 0 Dom E)
06-40
Printed in China
Modular
telephone
line jack
Wall plate
2 Rights of the Telephone Company
Should your equipment cause trouble on y our line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance;
(2) afford you the opportunity to correct the situation; and (3) inform you of your right
to bring a complaint to the Commission pursuant to procedures set forth in Subpart E
of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
intErfErEncE informAtion
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from
that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
HEAring Aid compAtibility (HAc)
This telephone system meets FCC standards for Hearing Aid Compatibility.
licEnsing
Licensed under US Patent 6,427,009.
fcc rf rAdiAtion ExposurE stAtEmEnt
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.”
introduction
CAUTION: When using telephone equipment, there are
basic safety instructions that should always be followed.
Refer to the IMPORTANT SAFETY INSTRUCTIONS provided
with this product and save them for future reference.
IMPORTANT: Because cordless phones operate on electricity,
you should have at least one phone in your home that isn’t
cordless, in case the power in your home goes out.
bEforE you bEgin
Parts Checklist
Make sure your package includes the items shown here.
3. Plug one end of the straight telephone line cord into the jack on the bottom
of the base.
4. Feed the line cord through the groove and plug the end into the modular
telephone jack.
5. Slip the mounting holes (on the bottom of the base) over the wall plate posts
and firmly slide the unit down into place.
progrAmming tHE tElEpHonE
Standby Screen
The handset displays the handset name, date, time, signal and battery status.
The base displays the current date and time.
Programming Functions
The system uses a menu structure to give you access to all of the built-in
features. You may program the following items in main menu: Setup HS, Setup
BS, and Date/Time.
NOTE: If the handset is not registered, or is out of range,
Setup BS and Date/Time are not programmable, and
Unavailable displays as you try to enter these two menus.
NOTE: During programming, you may press the mute/Clear
button at any time to exit the sub-menu and return to the
main menu, or press Flash/Exit to exit programming and
return to standby screen.
NOTE: If no key is pressed for 60 seconds, the handset will
automatically exit programming and return to standby
screen.
Setup HS
1. Make sure your phone is OFF (not in talk mode).
2. Press the Menu button to go to the main menu.
3. Press cid/vol (- or +) button to scroll to Setup HS.
4. Press Menu button to confirm and you may program the following items: Ring
Volume, Tones, Auto Talk, Handset Name and Language.
Language
From the Setup HS Menu:
1. Press the cid/vol (- or +) button to scroll to the Language sub-menu.
2. Press Menu button to enter the menu.
3. Use the cid/vol (- or +) button to select English, Français or Espanol. The
default setting is English.
4. Press the Menu button to save your selection.
Ring Volume
There are 4 volume levels for your selection. They are Volume 1 to 3 and Ringer
off respectively.
From the Setup HS Menu:
1. Press the cid/vol (- or +) button to scroll to the Ring Volume sub-menu.
2. Press Menu button to enter the menu.
Use the
cid/vol (- or +)
button to scroll to
your selection.
The default setting is VOL 3.
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
HAndsEt lAyout
Model 27903
2.4 GHz Cordless
Telephone System
User’s Guide
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a modular
jack, call your local phone company to find out how to get
one installed.
instAllAtion
Digital Security System
Your cordless phone uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate at
frequencies that may cause or receive interference with
nearby TVs, microwave ovens, and VCRs. To minimize or
prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV, microwave ovens,
or VCR. If such interference continues, move the cordless
telephone farther away from these appliances.
Certain other communications devices may also use the 2.4
GHz frequency for communication, and, if not properly set,
these devices may interfere with each other and/or your new
telephone. If you are concerned with interference, please
refer to the owner’s manual for these devices on how to
properly set channels to avoid interference. Typical devices
that may use the 2.4 GHz frequency for communication
include wireless audio/video senders, wireless computer
networks, multi-handset cordless telephone systems, and
some long-range cordless telephone systems.
Telephone
line cord
AC power
adaptor
Handset
battery pack
Base
Handset
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: To ensure proper battery installation, the connector is
keyed and can be inserted only one way.
3.
Press the
Menu
button to save your selection and the new volume setting
shows in the display.
NOTE:
Ringer can be disabled by pressing the mute/Clear/Ringer
on/off button in standby mode, please refer to “Ringer On/Off”.
Tones
From the Setup HS Menu:
1. Press the cid/vol (- or +) button to scroll to the Tones sub-menu.
2. Press Menu button to confirm and you may program the following items: Low
Battery, No Coverage and Key Tone.
3.
Use the
cid/vol (- or +)
button to scroll to the item you want to program and
press Menu button to enter.
Low Battery - You may set the warning beep to “On” when your handset
battery is low, so as to alert you to charge the battery. Press the cid/vol (- or
+) button to scroll to On or Off, then press Menu button to save the setting.
The default setting is On.
No Coverage - You may set the warning beep to “On” or “Off” when the
handset is out of range. Press the cid/vol (- or +) button to scroll to On or Off,
then press Menu button to save the setting. The default setting is On.
Key Tone - You may set the key tone to “On” or “Off” when you press buttons.
Press the cid/vol (- or +) button to scroll to On or Off, then press Menu button
to save the setting. The default setting is On.
Auto Talk
This option allows you to pick up the handset from base to answer an incoming
call without pressing the TALK/call back button.
From the Setup HS Menu:
1. Press the cid/vol (- or +) button to scroll to the Auto Talk sub-menu.
2. Press Menu button to enter the menu.
Use the
cid/vol (- or +)
button to scroll to
your selection.
The default setting is On.
3.
Press the
Menu
button to save your selection.
Handset Name
From the Setup HS Menu:
1. Press the cid/vol (- or +) button to scroll to the Handset name sub-menu.
2. Press Menu button to enter the menu. The default setting is Handset.
3. Use the touch-tone pad to enter a name (up to 13 characters). More than
one letter is stored in each of the number keys. For example, to enter Bill
Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the
letter I. Press the 5 key 3 times for the letter L. Press the 5 key 3 times for the
second letter L, and press the 1 key to insert a space between the first and
last name. Press the 7 key 4 times for the letter S; press the 6 key once for the
letter M; press the 4 key 3 times for the letter I; press the 8 key for the letter T;
press the 4 key twice for the letter H.
NOTE: If you make a mistake, press cid/vol (- or +) button to
move the cursor forward or backward, then use the mute/
Clear button to backspace and delete one character at a time.
4. Press the Menu button to save your name. You will hear a confirmation tone
and the display shows Saved.
Setup BS
1. Make sure your phone is OFF (not in talk mode).
2. Press the Menu button to go to the main menu.
3. Press cid/vol (- or +) button to scroll to Setup BS.
4. Press Menu button to confirm and you may program the following items: LAC
(local area code) and Dial mode.
Area Code
The telephone uses the pre-programmed area code to determine the
number format to display when a valid Caller ID record is received. The pre-
programmed area code is also used for the Dialback feature.
From the Setup BS Menu:
1. Press the cid/vol (- or +) button to scroll to the Area code sub-menu.
2. Press Menu button to enter the menu. Enter area code shows in the display.
3. Use the touch-tone pad to enter your 3-digit area code.
4. Press Menu button to save the setting.
Dial Mode
From the Setup BS Menu:
1. Press the cid/vol (- or +) button to scroll to the Dial mode sub-menu.
2. Press Menu button to enter the menu and use the cid/vol (- or +) button to
select Tone or Pulse.
3. Press Menu button to save your selection.
Date/Time
1. Make sure your phone is OFF (not in talk mode).
2. Press the Menu button to go to the main menu and use cid/vol (- or +) button
to scroll to Date/Time.
3. Press Menu button to enter the menu. Year 2006 shows in the display.
4. Use the touch-tone pad to enter the last two digits of the current year (range:
00 to 99).
5. Press Menu button to save the year setting and proceed to date setting.
6. Date 01/01 shows in the display. Use the touch-tone pad to enter two digits
for current month and day respectively.
7. Press Menu button to save the month/date setting and proceed to time
setting.
8. Time 12:01p shows in the display. Use the touch-tone pad to enter four digits
for current time and use cid/vol (- or +) button to scroll through “p” (pm) and
“a” (am).
9. Press Menu button to save the setting. Saved shows in the display.
Telephone Operation
Charge/In Use Indicator on Base
The charge/in use indicator on the base will flash to alert you to an incoming
call, during paging, or if you have a message waiting from your service provider.
The indicator will remain lit when a handset is in the base charging or when the
line is in use.
Making a Call
1. Press the TALK/call back button. Dial the desired number.
- OR -
Dial the number first, then press the TALK/call back button.
2. When finished, press the TALK/call back button or put the handset back into
the base cradle to hang up.
NOTE: If you want to delete the pre-dial number you entered,
press the mute/Clear button until all of the digits are erased.
Answering Calls
1. When the phone rings, press the TALK/call back button.
2. When finished, press the TALK/call back button or put the handset back into
the base cradle to hang up.
NOTE: If you have turned the Auto Talk function on, you can
pick up the handset from the base to answer the incoming
call directly, without pressing any buttons.
NOTE: Adjust the handset volume by pressing the
cid/vol (- or
+)
button during a call.
Inserting a Pause in the Dialing Sequence
Press the #pause button twice to insert a delay in dialing sequence when a
pause is needed to wait for a dial tone (for example, after you dial 9 for an
outside line, or to wait for a computer access tone.) Each pause counts as one
digit in the dialing sequence, and is shown as P in the display.
Redial
To quickly redial a number you dialed:
1. Make sure the phone is OFF (not in talk mode).
2. Press the TALK/call back button.
3. Press the redial button first, then use the cid/vol (- or +) button to select the
desired redial number.
NOTE: You may choose from 10 last dialed numbers.
4. Press the Menu button. The number dials automatically.
-OR-
1. Make sure the phone is OFF (not in talk mode).
2. Press the redial button. Then use the cid/vol (- or +) button to select the
desired redial number.
NOTE: You may choose from 10 last dialed numbers.
3. Press the TALK/call back button. The number dials automatically.
Editing a Redial Record Before Dialing
1. Make sure the phone is OFF (not in talk mode).
2. Press the redial button first, then use the cid/vol (- or +) button to select the
desired redial number.
3. Press the Menu button.
4. Press cid/vol (- or +) button to scroll to Select.
5. Press the Menu button to enter edit mode.
6. Press cid/vol (- or +) button to move the cursor forward or backward. Use the
touch-tone pad to add digits or press the mute/Clear button to backspace
and delete one digit at a time.
7. After editing, press TALK/call back to dial the modified redial number.
Storing a Redial Record in Phone Book
1. Make sure the phone is OFF (not in talk mode).
2. Press the redial button first, then use the cid/vol (- or +) button to scroll to the
desired redial number.
3. Press the Menu button.
4. Press cid/vol (- or +) button to scroll to Save number.
5. Press the Menu button to enter edit mode.
6. Enter name shows in the display. Input a name. Please refer to section
“Handset Name” for name editing method.
NOTE: A name must be input otherwise the record cannot be
stored.
7. Press the Menu button to save. Saved shows in the display. Repeat steps 2
through 7 to save other records.
Deleting a Redial Record
1. Make sure the phone is OFF (not in talk mode).
2. Press the redial button first, then use the cid/vol (- or +) button to select the
desired redial number.
3. Press the Menu button.
4. Use the cid/vol (- or +) button to scroll to Delete?.
5. Press the Menu button to delete the record showing in the display. Confirm?
shows in the display.
6. Press the Menu button again to confirm the deletion. Deleted shows in the
display.
NOTE: Press the Flash/Exit button to return to the standby
mode without deleting any redial records.
Deleting All Redial Records
1. Make sure the phone is OFF (not in talk mode).
2. Use the cid/vol (- or +) button to display any redial record.
3. Press the Menu button.
4. Use the cid/vol (- or +) button to scroll to Delete all?.
5. Press the Menu button. Confirm? shows in the display.
6. Press the Menu button again to confirm the deletion. All deleted shows in the
display.
NOTE: Press the Flash/Exit button to return to the standby
mode without deleting any redial records.
Call Timer
After you press the TALK/call back button on the handset, the built-in call timer
shows on the display and counts the length of time of the call in minutes and
seconds.
Wall mount
bracket
bAsE lAyout
Handset hook Page button
charge/in use
indicator
display
TALK/call back
(button)
cid/vol +/- (caller ID/
volume +/- button)
redial (button)
#pause
(button)
Flash/Exit
(button)
mute/Clear/
ringer on/off
(button)
Format (button)
Menu (button)
*tone (button)
Phonebook (button)
display
Aim at the socket and push
Rotate
instAlling tHE pHonE
Installing the Handset Battery
NOTE: You must connect the handset battery before use.
CAUTION: To reduce the risk of fire or personal injury, use
only the Thomson Inc. approved Nickel-metal Hydride
(Ni-MH) battery model 5-2734, that is compatible with this
unit.
1. Locate battery which is packaged inside a plastic bag and is separate from
the handset.
2. Locate the battery compartment on the back of the handset.