Filter
Top Products
Introduction
CAUTION: When using telephone equipment, there
are basic safety instructions that should always
be followed. Refer to the IMPORTANT SAFETY
INSTRUCTIONS provided with this product and save
them for future reference.
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your home
goes out.
Model 25952 Series
5.8 GHz Cordless
Handset
Speakerphone
Answering System
User’s Guide
Equipment Approval Information
Your telephone equipment is approved for connection to the Public Switched
Telephone Network and is in compliance with parts 15 and 68, FCC Rules and
Regulations and the Technical Requirements for Telephone Terminal Equipment
published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the
US number and Ringer Equivalence Number (REN) for the equipment. You must,
upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number
is called. In most (but not all) areas, the sum of the RENs of all devices connected
to one line should not exceed 5. To be certain of the number of devices you may
connect to your line as determined by the REN, you should contact your local
telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone
company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use
your own telephone equipment if you are on a party line. Check with your local
telephone company.
• Notice must be given to the telephone company upon permanent disconnection
of your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this product does not disable your alarm
equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
4. Place the handset in the base cradle. The charge/in use indicator turns on,
verifying the battery is charging. The unit will take 20 seconds to register
and verify its security code. READY shows in the display.
NOTE: In case of a power failure, the handsets may display
UNAVAILABLE
when the TALK/CALL BACK button is pressed.
You must then place all handsets on the main base cradle
for 20 seconds to re-register.
5. Allow the phone to charge for 16 hours prior to first use. If you don’t
properly charge the phone, battery performance is compromised.
CAUTION: To reduce risk of personal injury, fire, or
damage use only the 5-2732 power adaptor listed in
the user’s guide. This power adaptor is intended to
be correctly orientated in a vertical or floor mount
position.
Wall Mounting
1. Turn the base over.
2. Attach the wall mounting pedestal by first inserting the tabs on the open
edge of the pedestal into the slots on the lower portion of the bottom of
the base. Then push down and snap the pedestal into place.
3. Slip the mounting holes (on the back of the base) over the wall plate posts,
and slide the unit down into place. (Wall plate not included.)
NOTE : If desired, gather the extra telephone line and
power adaptor cord and store inside the wall mounting
pedestal.
Answering System Setup
This section shows you how to set up your answering system to receive
incoming calls. Before you begin the set up process, you must turn on the
answering system.
• Press the ans on/off button to turn the answering system ON and OFF.
The MESSAGES indicator lights when the answering system is
ON. The
indicator blinks when you have new messages.
NOTE: The answering system displays “- -” when it is OFF.
Setting the Voice Prompt Language
The default voice prompt language is English.
To change the answering system’s voice prompt language, press and hold
the skip button for two seconds. The unit announces “SELECCIONADO
ESPANOL” (Spanish selected).
NOTE: To change to English, press and hold the skip button
again for 2 seconds. The unit announces “ENGLISH IS
SELECTED”.
NOTE: In remote access mode, the system follows the
selected language. The voice prompt language cannot be
switched remotely.
Voice Time/Day Stamp
1. Make sure the answering system is ON.
2. Press and hold the day/check button on the base to set the day of the
week.
3. Press and hold the hour button on the base to set the hour (a.m. or p.m.).
Example: 12AM, 1AM, or 12PM, 1PM.
4. Press and hold the min button on the base to set the minute. The time
advances in 5-minute intervals, or tap and release to advance in 1 minute
intervals.
Speaker Volume
Use the speaker volume (- / +) buttons to adjust speaker volume on the
base to a comfortable level. L1 is the minimum speaker volume and L8 is
the maximum.
Recording the Outgoing Announcement
For best results when recording, you should be about nine inches from the
microphone, and eliminate as much background noise as possible.
1. Make sure the answering system is ON.
2. Press and hold the announce button on the base.
3. Begin speaking after you hear the beep.
4. Release the button when you finish your announcement.
NOTE: If you choose not to record an outgoing announcement,
a default announcement plays instead. To return to the default
announcement after you have recorded your own outgoing
announcement, press the announce button and release it when
you hear the beep.
Sample Outgoing Announcement
“HI, THIS IS (USE YOUR NAME HERE), I CAN’T ANSwER THE PHONE RIGHT
NOw, SO PLEASE LEAVE YOUR NAME, NUMBER AND A BRIEf MESSAGE
AfTER THE TONE, AND I’LL GET BACk TO YOU. THANkS.”
Reviewing the Announcement
Press and release the announce button to review your outgoing
announcement.
Rings to Answer
Use the RINGS TO ANSWER switch on the back of the base to set the number
of times you want the phone to ring before the answering system answers
the call. You may choose 3 rings, 5 rings, or TOLL SAVER (TS).
NOTE: If you select Toll Saver (TS) the unit answers after the
3rd ring if there ARE new messages, OR the unit answers
after the 5th ring if there ARE NO new messages.
Handset Setup
There are nine programmable menus available: Language, Handset Name,
Area Code, Ringer ON/OFF, Ringer Tone, VIP Ring Tone, Tone/Pulse, Transfer
and Default Setting.
During programming, you may press the mute/menu button at any time to
go to the next option. Pressing mute/menu button takes you through the
menu choices. When changes have been made to selected menu item,
pressing the mute/menu button saves the changes and Confirmation Tone
sounds. To exit the menu and keep the previous setting and return to the
standby mode, press the *EXIT/tone button.
Display Language
1. Press the mute/menu button until 41ENG 2fRA 3ESP shows in the
display. 1ENG is the default. (ENG stands for English. FRA stands for
French. ESP stands for Spanish.)
2. Use the
CALLER ID-VOLUME (5
or
6)
button or the touch-tone pad on
the handset to enter your selection.
3. Press mute/menu again to save.
Handset Name
1. Press the mute/menu button until ENTER NAME shows in the display.
2. Use the touch-tone pad to enter the name (up to 15 characters). More
than one letter is stored in each of the number keys. For example, to
enter the name Bill Smith, press the 2 key twice for the letter B. Press
the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter
L. Wait for one second. Press the 5 key 3 times for the second letter L.
Press th e 1 key to insert a space between the L and the S. Press the 7
key 4 times for the letter S; press the 6 key once for the letter M; press
the 4 key 3 times for the letter I; press the 8 key for the letter T; press
the 4 key twice for the letter H.
NOTE: If you make a mistake, use the chan/delete button
to backspace and delete one character at a time.
3. Press mute/menu again to save.
NOTE: If no name is entered, READY shows in the display.
Local Area Code
This program setup allow you to setup how the incoming caller ID show on
the display.
1. Press the mute/menu button until AREA CODE - - - shows in the
display. “- - -” is the default.
2. Use the touch-tone pad on the handset to enter your three digit area code.
3. Press mute/menu again to save.
NOTE: If you make a mistake, press the chan/delete button
to erase a wrong number.
Ringer ON/OFF
1. Press the mute/menu button until RINGER 41 ON shows in the
display. 1ON is the default.
2. Use the
CALLER ID-VOLUME (5
or
6)
button or the touch-tone pad on the
handset to scroll to 1 ON or
2 Off.
3. Press mute/menu to save.
NOTE: If you turn the ringer off, RINGER Off shows on the
display.
Ringer Tone
You can choose from 10 ringtones.
1. Press the mute/menu button until RINGER TONE 401 shows in the
display. 01 is the default.
2. Use the
CALLER ID-VOLUME (5
or
6)
button or the touch-tone pad on the
handset to select from 01 to 10.
3. Press mute/menu to save.
VIP Ring Tone
This feature allows you to assign a specific ring tone to a number stored in
Memory. It is recommended that you store a Caller ID record into Memory
for this purpose.
1. Press the mute/menu button until VIP RING TONE shows in the display.
2. Press the desired memory location (0 through 9). If there is a number
stored in the selected memory location, VIP RT 4DEfAULT shows in the
display.
3. Press
CALLER ID-VOLUME (5
or
6)
on the handset to select from 01 to
10 or
DEfAULT to use ring tone set in the Ringer Tone Menu or SILENT to
silence ringer.
4. Press mute/menu to save.
NOTE: Delete the memory record will also delete the VIP
ring tone.
Tone/Pulse
1. Press the mute/menu button until 41 TONE 2 PULSE shows in the
display. 1 TONE is the default.
2. Use the
CALLER ID-VOLUME (5
or
6)
button or the touch-tone pad on
the handset to scroll to 1 TONE or 2 PULSE.
3. Press mute/menu to save.
Transfer ON/OFF
In order to use the Call Transfer feature (applicable ONLY with additional
handsets), you must have the Transfer ON/OFF set to ON through the menu
of the transferring handset.
1. Press the mute/menu button until TRANSfER 41Off shows in the display.
2. Use the CALLER ID-VOLUME (
5
or
6
) button or the touch tone pad on the
handset and select 2ON.
3. Press mute/menu again to save.
Default Setting
You may return handset settings to the factory default setup using this
menu.
1. Press the mute/menu button until DEfAULT 4NO shows in the display.
NO is the default.
2. Use the CALLER ID-VOLUME (
5
or
6
) button on the handset to scroll to
YES or NO.
NOTE: If you choose YES, all settings in the programmable
menu return to the factory defaults.
3. Press mute/menu to save.
Cordless Phone Basics
Charge/In Use Indicator
The phone is ON when the charge/in use indicator on the base is lit. The handset
visual ringer and base indicator flash when you receive a call.
Answering a Call
1. When the phone rings, pick up the handset and press the TALK/CALL BACK
or SPEAKER button.
2. When finished, press the TALK/CALL BACK or SPEAKER button again or
place the handset on the base cradle to hang up.
Making a Call
1. Pick up the handset and press the TALK/CALL BACK or SPEAKER button.
Wait for the dial tone. The call timer starts counting minutes and seconds
in the display.
2. Dial a telephone number.
3. When finished, press the TALK/CALL BACK or SPEAKER button again or
place the handset on the base cradle to hang up.
NOTE: In case of power failure, the handset may display
UNAVAILABLE
when the TALK/CALL BACK or SPEAKER
button is pressed. You must then place the handset on the
main base for 20 seconds to reset the unit.
Pre-dialing
1. Make sure the phone is OFF (not in TALK mode).
2. Dial a telephone number (the number you dial shows in the display).
NOTE: If you make a mistake dialing the number, use the
chan/delete button to backspace and erase the wrong
number, and enter the correct number.
3. Press the TALK/CALL BACK or SPEAKER button on that handset. The
number automatically dials and the call timer starts counting the minutes
and seconds in the display.
4. When finished, press the TALK/CALL BACK or SPEAKER button again to
hang up.
NOTE : You may enter up to 32 pre-dial digits.
Redial
While the phone is ON (in TALK or SPEAKERPHONE mode), press the redial
button to redial the last number you dialed (up to 32 digits).
- OR -
While the phone is OFF (in standby mode), press the redial button and then
the TALK/CALL BACK or SPEAKER button to redial the last number.
Flash
Use the flash/answerer/call waiting button to activate custom calling
services such as call waiting, which are available through your local phone
company.
TIP: Do not use the TALK/CALL BACK button to activate
custom calling services such as call waiting or you’ll hang
up the phone.
Thomson Inc.
101 West 103rd Street
Indianapolis, IN 46290-1102
© 2007 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Model 25952
00017254 (Rev. 1 Dom E/S)
07-39
Printed in China
Before You Begin
Parts Checklist
(for 25952xx1 model)
Make sure your package includes the items shown here.
Modular
telephone
line jack
Wall plate
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Channel Button
While talking on the phone, it may be necessary for you to manually change
the channel to improve reception and reduce noise or static on the line. Press
and release the chan/delete button to move to the next clear channel.
Exit
Press the *EXIT/tone button to cancel any command you initiated.
Page
This feature assists in locating a misplaced handset.
Press the page button on the base. The handset beeps continuously for
about 2 minutes until you press the TALK/CALL BACK or SPEAKER button on
the handset or the page button on the base.
NOTE: You may still page the handset when the ringer is
off.
Do Not Disturb
This feature allows you to turn off handset ringers for all handsets
registered with the base unit. The answerer speaker will be silenced
when the unit is receiving incoming messages.
Press the
do not disturb
button on the base. Handset will display DO NOT
DISTURB.
NOTE: If DO NOT DISTURB is activated during an incoming
ring, it will only be effective from the next incoming call.
Ringer ON/OFF Shortcut
Apart from the setting in the main menu, there is a shortcut to set the ringer.
Make sure the phone is OFF (not in talk mode).
1. Press the #PAUSE/ringer button to go to the RINGER
ON/Off menu.
RINGER 41 ON shows in the display. 1ON is the default.
2. Use the CALLER ID-VOLUME (
5
or
6
) button or the touch-tone pad on the
handset to scroll to 1 ON, or
2 Off.
3. Press the #PAUSE/ringer button to save your selection. You will hear a
confirmation tone.
Volume
When the phone is ON (in TALK or SPEAKERPHONE mode) press the CALLER
ID-VOLUME (
5
or
6
) button to adjust the listening level. Choose from five
volume settings. VOL 1 is the lowest volume and VOL 5 is the highest volume.
NOTE: The phone will automatically reset VOL 5 to VOL 4
after you hang up.
Mute
Use mute during a phone conversation to speak privately and off-line with a
third party.
1. Press the mute/menu button. MUTE shows in the display. The party on the
telephone will not hear you.
2. Press the mute/menu button when finished.
Switching between the Speakerphone and
Handset
1. If you are using the handset earpiece and want to switch to the
speakerphone, press the SPEAKER button, you can then press SPEAKER
button again to end conversation.
2. If you are using the speakerphone and want to switch to the handset
earpiece, press the TALK/CALL BACK button, you can then press the TALK/
CALL BACK button again to end conversation.
Temporary Tone
This feature is useful only if you have pulse (rotary) service. Temporary Tone
Dialing enables pulse (rotary) service phone users to access touch tone
services offered by banks, credit card companies, etc. For example, when
you call your bank you may need to enter your bank account number.
Temporarily switching to touch tone mode allows you to send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the *EXIT/tone button on the handset to
temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse
(rotary)
dialing mode.
Call Transfer (applicable only with additional
handsets)
During an external call, you may transfer the external call to another
handset.
NOTE: The transfer feature MUST be set to ON, this can
be done through each handset’s setup menu function,
Transfer ON/OFF.
1. Press the format/trans button on the originating handset. TRANSfERRING
shows in the display. All registered handsets will be paged.
2. Press the format/trans button or TALK/CALL BACK on receiving handset to
answer call.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
2 Rights of the Telephone Company
Should your equipment cause trouble on y our line which may harm the telephone
network, the telephone company shall, where practicable, notify you that
temporary discontinuance of service may be required. Where prior notice is not
practicable and the circumstances warrant such action, the telephone company
may temporarily discontinue service immediately. In case of such temporary
discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation;
and (3) inform you of your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the
operation of its business and not inconsistent with FCC Rules and Regulations. If
these changes are expected to affect the use or performance of your telephone
equipment, the telephone company must give you adequate notice, in writing, to
allow you to maintain uninterrupted service.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from
that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
Base Layout
Your new GE telephone system is EXPANDABLE
up to a total of 4 handsets (by purchase of optional
Model 25902 handset with charge cradle)
Handset Layout
Base
Handset
Belt
clip
Telephone
line cord
AC power
adaptor
Handset
battery pack
Battery
compartment
cover
Wall mount
bracket
display
TALK/CALL BACK
(button)
CALLER ID-
VOLUME (6)
(button)
CALLER ID-
VOLUME (5)
(button)
chan/delete
(channel/delete button)
redial
(button)
*EXIT/tone
(button)
#PAUSE/ringer
(button)
flash/answerer/
call waiting (button)
format/trans
(format/transfer
button)
mem
(memory
button)
SPEAKER
(button)
mute/menu
(button)
play stop
(button)
skip (button)
erase
(button)
repeat
(button)
visual ringer
page
(button)
charge/in use
(indicator)
erase
(button)
PLAY/STOP
(button)
8 skip
(button)
7 repeat
(button)
ans on/off
(answerer on/off
button)
announce
(button)
day/check
(button)
hour
(button)
min
(minute button)
memo
(button)
volume (-/+)
(buttons)
MESSAGES
(indicator)
do not disturb
(button)
Rings To
Answer
Visit the GE website at: www.GE.com/phones
Installing the Phone
Installing the Handset Battery
NOTE: You must connect the handset battery before use.
CAUTION: To reduce the risk of fire or personal injury,
use only the Thomson Inc. approved Nickel-Cadmium
(Ni-Cd ) battery model 5-2729 or Nickel-Metal Hydride
(Ni-MH) battery model 5-2522, which is compatible with
this unit.
1. Locate battery and battery door which are packaged together inside a
plastic bag and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment. PLEASE
REGISTER shows in the display.
NOTE: To ensure proper battery installation, the connector
is keyed and can be inserted only one way.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into
place.
Base Station
1. Choose an area near an electrical outlet and a telephone wall jack
(RJ11C), and place your cordless
telephone on a level surface,
such as a desktop or tabletop, or
you may mount it on the wall.
2. Plug one end of the telephone
line cord into the TEL LINE jack
at the back of the base and the
other end into a modular jack.
3. Plug the AC power converter
into the electrical outlet and the DC connector into the jack at the back of
the base.
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
NOTE: To cancel the call transfer, you may press *EXIT/
tone button or the
format/trans
button on the originating
handset.
NOTE: If there is no answer within 2 minutes after
transferring the call, then the handsets will be rung back
(callback). If no handset answers within 30 seconds, then
the external call will be automatically dropped.
Caller ID (CID)
IMPORTANT: In order to use this unit’s Caller ID features,
you must subscribe to either the standard Name/Number
Caller ID Service or Call Waiting Caller ID Service. To
know who is calling while you are on the phone, you must
subscribe to Call Waiting Caller ID Service.
This unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date, and time; or
the name, phone number, date, and time.
Call Waiting Caller ID
Provided you subscribe to Call Waiting Caller ID service from your phone
company; if you receive an incoming call and you are already on the phone,
a beep indicates the presence of a Call Waiting call on the line. Only the
handset that is in use at the time of the call will display and store the Call
Waiting Caller ID information.
• When you hear the call waiting beep in the handset receiver, press the
flash/answerer/call waiting button to put the current call on hold and
answer the incoming call. Press flash/answerer/call waiting again to return
to the original call.
Receiving CID Records
When you receive a call, the Caller ID information is transmitted between the
first and second ring. The Caller ID information appears on the display while
the phone rings, giving you a chance to monitor the information and decide
whether or not to answer the call.
Storing CID Records (In CID Memory)
If you are not at home or cannot answer, your telephone’s Caller ID memory
stores the data for the 40 most recent calls you received so you can see who
called while you were unavailable. When the 41st call is received, the oldest
Caller ID record (1st call) is automatically deleted.
You may review the stored information at any time. Calls received since your
last review show as
NEw in the display. Calls that have not been previously
reviewed but were received from the same number more than once show as
REPT in the display.
Reviewing CID Records
As calls are received and stored, the display is updated to let you know how
many calls have been received. To scroll CID records:
1. Make sure the phone is OFF (not in talk mode).
2. Press the CALLER ID-VOLUME (
6
) button to review the newest CID record.
3. Press the CALLER ID-VOLUME (
5
) button to review the oldest CID record
first.
Dialing a CID Number
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CALLER ID-VOLUME (
5
or
6
) button to display the desired record.
3. Press the TALK/CALL BACK or SPEAKER button. The number dials
automatically.
NOTE: Depending on (a) how the incoming caller’s phone
number is formatted when it is received, and (b) whether or
not you previously pre-programmed your local area code
into the set up menu, you may need to adjust the format of
the incoming caller’s stored phone number before making
the call, press the format/trans button to adjust the
number, and try again
Available formats include:
Number of digits Explanation Example
Eleven digits long distance code “1 ” 1-317-555-8888
+3-digit area code
+7-digit telephone number.
Ten digits 3-digit area code + 317-555-8888
7-digit telephone number.
Seven digits 7-digit telephone number. 555-8888
For Model 25952xx2 there will be ONE additional handset, charge cradle,
belt clip, battery pack and cover than shown above.
For Model 25952xx3 there will be TWO additional handsets, charge cradles,
belt clips, battery packs and covers than shown above.
For Model 25952xx4 there will be THREE additional handsets, charge
cradles, belt clips, battery packs and covers than shown above.
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a modular
jack, call your local phone company to find out how to
get one installed.
Installation
Digital Security System
Your cordless phone uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate
at frequencies that may cause or receive interference
with nearby TVs, microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV,
microwave ovens, or VCR. If such interference continues,
move the cordless telephone farther away from these
appliances.
Certain other communications devices may also use the
5.8 GHz / 900 MHz frequency for communication, and, if
not properly set, these devices may interfere with each
other and/or your new telephone. If you are concerned
with interference, please refer to the owner’s manual for
these devices on how to properly set channels to avoid
interference. Typical devices that may use the 5.8 GHz
frequency for communication include wireless audio/video
senders, wireless computer networks, multi-handset
cordless telephone systems, and some long-range cordless
telephone systems.
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, fluorescent lighting,
microwave ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Time
Date
Caller ID record number
Caller ID name
Caller ID phone number
Caller status; NEW or REPT