Filter
Top Products
Your telephone equipment is approved for connection to the Public Switched Telephone Network
and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical
Requirements for Telephone Terminal Equipment published by ACTA.
On the bottom of this equipment is a label indicating, among other information, the US number
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line
and still have all of these devices ring when your telephone number is called. In most (but not
all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be
certain of the number of devices you may connect to your line as determined by the REN, you
should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instructions for
details.
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own
telephone equipment if you are on a party line. Check with your local telephone company.
1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment. PLEASE REGISTER
shows in the display.
2. Plug one end of the telephone line cord into the TEL LINE jack at the back of the base
and the other end into a modular jack.
3. Plug the AC power converter into the electrical outlet and the DC connector into the
jack at the back of the base.
4. Place the handset in the base cradle. The charge/in use indicator turns on, verifying
the battery is charging.
The unit will take 20 seconds to register and verify its security
code. READY shows in the handset’s display.
UNAVAILABLE
5. Allow the phone to charge for 16 hours prior to rst use. If you don’t properly charge
the phone, battery performance is compromised.
1. Turn the base over.
2. Attach the wall mounting pedestal by rst inserting the tabs on the open edge of
the pedestal into the slots on the lower portion of the bottom of the base. Then push
down and snap the pedestal into place.
3. Slip the mounting holes (on the back of the base) over the wall plate posts, and slide
the unit down into place. (Wall plate not included.)
There are nine programmable menus available: Language, Handset Name, Area Code,
Ringer On/Off, Ringer Tone, VIP Ring Tone, Tone/Pulse, Transfer and Default Setting.
During programming, you may press the mute/menu button at any time to go to the
next option. To exit the menu, keep the previous setting and return to the standby
mode, press the button.
1. Press the button until 41ENG 2FRA 3ESP shows in the display. 1ENG is
the default. (ENG stands for English. FRA stands for French. ESP stands for Spanish.)
2. Use the (5or6) button or the touch-tone pad on the handset
to enter your selection.
3. Press again to save.
1. Press the button until ENTER NAME shows in the display.
2. Use the touch-tone pad on the handset to enter the name (up to 15 character
s).
More than one letter is stored in each of the number keys. For example, to enter the
name Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the
letter I. Press the 5 key 3 times for the letter L. Wait for one second. Press the 5 key 3
times for the second letter L. Press the 1 key to insert a space between the L and the
S. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press
the 4 key 3 times for the letter I; press the 8 key for the letter T; press the 4 key twice
for the letter H..
3. Press again to save.
READY
1. Press the button until AREA CODE - - - shows in the display. “- - -” is
the default.
2. Use the touch-tone pad on the handset to enter your three digit area code.
3. Press again to save.
1. Press the button until RINGER 41 ON shows in the display.
1 ON is the default.
2. Use the
(5or6)
button or the touch-tone pad on the handset
to scroll to 1 ON or 2 OFF.
3. Press to save.
RINGER OFF
You can choose from 10 ringtones.
1. Press the button until RINGER TONE 401 shows in the display.
01 is the default.
2. Use the
(5or6)
button on the handset to select from 01 to 10.
3. Press to save.
This feature allows you to assign a specic ring tone to a number stored in Memory. It
is recommended that you store a Caller ID record into Memory for this purpose.
1. Press the button until VIP RING TONE shows in the display.
2. Press the desired memory location (0 through 9). If there is a number stored in the
selected memory location, VIP RT 4DEFAULT shows in the display.
3. Press
(5or6)
button on the handset to select from 01 to 10 or
DEFAULT to use ring tone set in the Ring Tone Menu or SILENT to silence ringer.
4. Press to save.
1. Press the button until 41 TONE 2 PULSE shows in the display.
1 TONE is the default.
2. Use the
C (5or6)
button or the touch-tone pad on the handset
to scroll to 1 TONE or 2 PULSE.
3. Press to save.
In order to use the Call Transfer feature (applicable ONLY with additional handsets), you
must have the Transfer ON/OFF set to ON through the menu of the transferring handset.
1. Press the button until TRANSFER 41 OFF shows in the display.
2. Use the
(5or6)
button or the touch tone pad on the handset
and select 2 ON.
3. Press again to save.
You may return handset settings to the factory default setup using this menu.
1. Press the button until DEFAULT 4NO shows in the display. NO is
the default.
2. Use the
(5or6)
button on the handset to scroll to YES or NO.
3. Press to save.
The phone is when the charge/in use indicator on the base is lit. The handset visual
ringer and base indicator ash when you receive a call.
1. When the phone rings, pick up the handset and press the or
button.
2. When nished, press the or button again or place the
handset on the base cradle to hang up.
1. Pick up the handset and press the or button. Wait for the
dial tone. The call timer starts counting minutes and seconds in the display.
2. Dial a telephone number.
3. When nished, press the or button again or place the
handset on the base cradle to hang up.
UNAVAILABLE
1. Make sure the phone is (not in TALK mode).
2. Dial a telephone number (the number you dial shows in the display).
3. Press the or button on that handset. The number
auto-matically dials and the call timer starts counting the minutes and seconds in
the display.
4. When nished, press the or button again to hang up.
While the phone is (in TALK or SPEAKERPHONE mode), press the button to
redial the last number you dialed (up to 32 digits).
- OR -
While the phone is (in standby mode), press the button and then the
or button to redial the last number.
Use the ash/call waiting button to activate custom calling services such as call
waiting, which are available through your local phone company.
While talking on the phone, it may be necessary for you to manually change the
channel to improve reception and reduce noise or static on the line. Press and release
the button to move to the next clear channel.
Press the button to cancel any command you initiated.
This feature assists in locating a misplaced handset.
Press the button on the base. The handset beeps continuously for about 2
minutes until you press the
or button on the handset or the
page button on the base.
Apart from the setting in the main menu, there is a shortcut to set the ringer. Make sure
the phone is (not in talk mode).
1. Press the button to go to the menu.
RINGER 41 ON shows in the display. 1 ON is the default.
2. Use the
(5or6)
button or the touch-tone pad on the handset
to scroll to 1 ON or 2 OFF.
3. Press the button to save your selection. You will hear a
conrmation tone.
When the phone is (in TALK or SPEAKERPHONE mode) press the
(5or6)
button to adjust the listening level. Choose from ve
volume settings. VOL 1 is the lowest volume and VOL 5 is the highest volume.
VOL 5VOL 4
For there will be additional handset, charge cradle, belt clip,
battery pack and cover than shown above.
For there will be additional handsets, charge cradles, belt clips,
battery packs and covers than shown above.
For there will be additional handsets, charge cradles, belt clips,
battery packs and covers than shown above.
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in
your home. If you don’t have a modular jack, call your local
phone company to nd out how to get one installed.
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Use mute during a phone conversation to speak privately and off-line with a third party.
1. Press the button. MUTE shows in the display. The party on the
telephone will not hear you.
2. Press the button when nished.
1. If you are using the handset earpiece and want to switch to the speakerphone, press
the button, you can then press button again to end conversation.
2. If you are using the speakerphone and want to switch to the handset earpiece, press
the button, you can then press the button again
to end conversation.
This feature is useful only if you have pulse (rotary) service. Temporary Tone Dialing
enables pulse (rotary) service phone users to access touch tone services offered by
banks, credit card companies, etc. For example, when you call your bank you may need
to enter your bank account number. Temporarily switching to touch tone mode allows
you to send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the button on the handset to
temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse (rotary)
dialing mode.
During an external call, you may transfer the external call to another handset.
1. Press the button on the originating handset. TRANSFERRING shows in
the display. All registered handsets will be paged.
2. Press the button or on receiving handset to answer
call.
This unit receives and displays information transmitted by your local phone company.
This information can include the phone number, date, and time; or the name, phone
number, date, and time.
• Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure
the installation of this product does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualied
installer.
Should your equipment cause trouble on y our line which may harm the telephone network,
the telephone company shall, where practicable, notify you that temporary discontinuance of
service may be required. Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue service immediately. In case
of such temporary discontinuance, the telephone company must: (1) promptly notify you of
such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3)
inform you of your right to bring a complaint to the Commission pursuant to procedures set
forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and not
inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or
performance of your telephone equipment, the telephone company must give you adequate
notice, in writing, to allow you to maintain uninterrupted service.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to corr
ect the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
“receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to
which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced
radio/television technician for additional suggestions. Also, the Federal Communications
Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference
Problems.” This booklet is available from the U.S. Government Printing Ofce, Washington, D.C.
20402. Please specify stock number 004-000-00345-4 when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,427,009.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines
when used with the belt clip supplied with this product. Use of other accessories may not ensure
compliance with FCC RF exposure guidelines.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
(for Model )
Make sure your package includes the items shown here.
1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and
place your cordless telephone on a level surface, such as a desktop or tabletop, or
you may mount it on the wall.
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
6
5
Provided you subscribe to Call Waiting Caller ID service from your phone company; if
you receive an incoming call and you are already on the phone, a beep indicates the
presence of a Call Waiting call on the line. Only the handset that is in use at the time of
the call will display and store the Call Waiting Caller ID information.
• When you hear the call waiting beep in the handset receiver, press the
button to put the current call on hold and answer the incoming call.
Press the
button again to return to the original call.
Model 25932
00017258 (Rev. 1 Dom E/S)
07-44
Printed in China
101 West 103rd St.
Indianapolis, IN 46290-1102
© 2007 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)