Extrasport 27930 Cordless Telephone User Manual


  Open as PDF
of 2
 
INTRODUCTION
Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services. You must subscribe to one of these services in
order to use this unit.
Your Caller ID phone enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 40 Caller ID messages sequentially.
• Know who called while you were away.
To get the most from your new phone, we suggest that you
take a few minutes right now to read through this user's
guide.
IMPORTANT: In order to use this unit, you must
subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.
IMPORTANT: Because cordless phones operate on
electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the items shown here.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.
When you place the handset in the base, the unit verifies
its security code. After a power outage or battery
replacement, you should place the handset in the base for
about 20 seconds to reset the code.
INSTALLATION
DESKTOP INSTALLATION
NOTE : For desktop charging only, the handset is able
to charge facing up or down.
1. Remove the battery compartment door on the handset,
insert the battery pack, plug the cord into the jack (inside
the compartment), and replace the compartment door.
2. Set the RINGER switch (on the handset) to ON and place
the handset in the cradle on the base.
3. Plug the telephone line cord into the TEL LINE jack on
the back of the base and into a modular jack.
4. Plug the power supply into the power jack on the back of
the base and the other end into an electrical outlet. The
"charge" indicator comes, verifying the battery is charging.
Allow the phone to charge for 12 hours prior to first use.
If you don't properly charge the phone, battery
performance will be compromised.
CAUTION: Use only the ATLINKS USA, Inc.
5-2501 power supply that came with this unit.
Using other power supplies may damage the unit.
NOTE : The phone is shipped in Tone Dialing Mode
from the manufacturer.
WALL MOUNT INSTALLATION
Because it is necessary to charge the handset for 12 hours
prior to connecting the phone for use the first time, it is
better to leave the unit on a flat surface during initial
charge before attempting to hang it on the wall.
1. Remove the battery compartment door on the handset,
insert the battery pack, plug the cord into the jack (inside
the compartment), and replace the compartment door.
2. Set the RINGER switch (on the handset) to ON and place
the handset in the cradle on the base.
3. Plug the power supply into the power jack on the back of
the base and the other end into an electrical outlet. The
"charge" indicator comes, verifying the battery is
charging.
Allow the phone to charge for 12 hours prior to first use.
If you don't properly charge the phone, battery
performance will be compromised.
NOTE: If desired, gather the extra power adapter line
cord together, fasten with a wire tie, and store inside
the wall mounting bracket.
4. Remove the handset from the cradle and set aside. Turn
the base over and align the four slots on the bottom of
the base with the four hook-tabs on the mounting
bracket.
5. Insert the hook-tabs into the slots and push upwards
until the mounting bracket snaps securely into place.
6. Plug the telephone line cord into the TEL LINE jack on
the back of the base and the other end into a modular
jack. If desired, gather the extra telephone line cord
together, fasten with a wire tie, and store inside the wall
mounting bracket.
NOTE: If desired, gather the extra telephone line
cord together, fasten with a wire tie, and store inside
the wall mounting bracket.
7. Slip the mounting holes on the bracket over the wall
plate posts and firmly slide the unit down into place
(wall plate not included).
8. Place the handset in the cradle.
NOTE : The phone is shipped in Tone Dialing Mode
from the manufacturer.
CAUTION: Use only the ATLINKS USA, Inc.
5-2501 power supply that came with this unit.
Using other power supplies may damage the unit.
SET UP
There are five programmable menus available: Language,
Area Code, Ringer Tone, Set Tone/Pulse, and Default Setting.
LANGUAGE SETTING SELECTION
1. Press the flash/program button until “
1ENGLISH 2FRA
3ESP
“ shows in the display. “
1ENGLISH
“ is the
default setting.
2. Use the CID review (up or down arrow) button or the
handset number pad to enter your selection.
3. Press flash/program to store selection. You will hear a
confirmation tone.
AREA CODE SELECTION
1. Press the flash/program button until
“SET AREA CODE - - -”
shows in the display. “
- - -”
is the default setting.
2. Use the handset number pad to enter your three digit
area code.
3. Press flash/program to store selection. You will hear a
confirmation tone.
RINGER TONE SELECTION
1. Press the flash/program button until “
SET RINGER
TONE123
” shows in the display.
“1”
is the default setting.
2. Use the CID review (up or down arrow) button or the
handset number pad to scroll to 1, 2, or 3.
3. Press flash/program to store selection. You will hear a
confirmation tone.
TONE/PULSE DIALING SELECTION
1. Press the flash/program button until “
SET TONE/PULSE”
shows in the display.
“1TONE”
is the default setting.
2. Use the CID review (up or down arrow) button or the
handset number pad to scroll to
1TONE
or
2PULSE
.
3. Press flash/program to store selection. You will hear a
confirmation tone.
DEFAULT SETTING SELECTION
1. Press the flash/program button until
DEFAULT
SETTING? 1YES 2NO
shows in the display.
“2NO”
is
the default setting.
2. Use the CID Review (up or down arrow) button or the
handset number pad to scroll to
1YES
or
2NO
.
3. Press flash/program to store selection. You will hear a
confirmation tone.
CORDLESS PHONE BASICS
RECEIVING A CALL
1. Check the display to see who is calling.
2. Press the TALK button.
MAKING A CALL
To make a call, press the TALK button before you dial and
press it again to hang up.
REDIAL
While the phone is on, press the redial/delete button to
redial the last number you dialed (up to 32 digits). If you
get a busy signal, and want to keep dialing the number,
just press redial/delete again (you don't have to turn the
phone off and back on).
FLASH
Use the flash/program button to activate custom calling
services such as call waiting or call transfer, which
are available through your local phone company.
TIP: Don’t use the TALK button to activate custom
calling services such as call waiting, or you’ll hang up
the phone.
IN USE INDICATOR
The phone is ON when the indicator on the handset
antenna is lit and the page/ in use indicator on the base is
lit. The antenna indicator and the in use indicator on the
base flashes when you receive a call.
CHANNEL BUTTON
While talking, you might need to manually change the
channel in order to get rid of static. Press and release the
chan button to advance to the next clear channel.
TEMPORARY TONE
This feature enables pulse (rotary) service phone users to
access touch-tone services offered by banks, credit card
companies, etc., by pressing the TONE button to temporarily
make the phone touch-tone compatible. To get information
about your bank account, for example, you would:
1. Call the bank’s information line.
2. Press the TONE button (*) after your call is answered.
3. Follow the voice instructions to complete your
transaction.
4. Hang up when finished. The phone returns to Pulse
(rotary) service.
HOLD
Press the hold button to put a call on hold.
HOLD
shows in
the display, and the handset antenna indicator flashes. To
release a line on hold, press the hold button again or pick
up an extension phone.
CANCEL
Press the cancel button to cancel any command you
initiated. Press cancel to hang up after finishing a call.
FINDING THE HANDSET
This feature helps to locate a misplaced handset.
Press the PAGE button on the base. The handset beeps
continuously for about 2 minutes or until you press the
TALK button on the handset..
NOTE: The ringer does not have to be on for this
feature to work.
RINGER SWITCH
The RINGER switch must be ON for the handset to ring
during incoming calls.
VOLUME
The VOLUME button controls the volume of the handset's
earpiece.
VOICE MESSAGING
Provided your phone company
offers voice messaging service
and you subscribe to it, the in
use/VMWI indicator on the base
flashes when the phone is not in
use to indicate there is a
message waiting. It stops
flashing after the message has
been reviewed.
CALLER ID FEATURES
This unit receives and displays information transmitted by
your local phone company. This information can include
the phone number, date, and time;
or
the name, phone
number, date, and time. The unit can store up to 40 calls
for later review.
CALLER ID WITH CALL WAITING
Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep. The caller
identification information appears in the display after you
hear the tone.
• Press the flash button to put the current person on hold
so that you can answer the incoming call.
IMPORTANT: In order to use the Caller ID functions
with this unit, you must subscribe to either the
standard Name/Number Caller ID Service or Caller
ID with Call Waiting Service. To know who is calling
while you are on the phone, you must subscribe to
Caller ID with Call Waiting Service.
RECEIVING AND STORING CALLS
When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.
When the memory is full, a new call automatically replaces
the oldest call in memory.
NEW
appears in the display for
calls received that have not been reviewed.
NOTE: Check with your local phone company
regarding name service availability.
REVIEWING RECORDS
As calls are received and stored, the display is updated to
let you know how many calls have been received.
• Press the CID review down button to scroll through the
call records from the most recent to the oldest.
• Press the CID review up button to scroll through the call
records from the oldest to the newest.
TRANSFERRING CID RECORDS TO
MEMORY
You may transfer a Caller ID record to your phone’s memory.
NOTE: It is important that you format CID records
correctly before storing in memory. It is not possible to
re-format CID records stored in memory.
1. Use the CID review (up or down arrow) button to scroll
to the desired record.
2. Press the mem button.
3. Press the desired memory location. Example, press the
number 1 key to store the record in memory location 1.
4. Press the mem button again to store.
DELETING RECORDS
Use the redial/delete button to erase the record currently
shown in the display or all records.
DELETING THE CURRENT RECORD
1. Make sure the phone is OFF.
2. Use the CID review (up or down arrow) buttons to
display the desired Caller ID record.
3. Press redial/delete. The display shows
DELETE CALL ID?
4. Press redial/delete again to erase the record. The display
shows
DELETED
.
DELETING ALL RECORDS
1. Make sure the phone is OFF.
2. Use the CID review (up or down arrow) buttons to
display any Caller ID record.
3. Press and hold redial/delete button until the unit beeps
and
DELETE ALL?
shows in the display.
4. Press redial/delete again to erase all records. The display
shows
DELETED
.
27930
40-Channel 2.4 GHz Caller ID with
Call Waiting Cordless Telephone
User's Guide
We bring good things to life.
Model 27930A
15729570 (Rev. 0 CAN E)
01-23
Printed in China
MODULAR JACK REQUIREMENTS
You need an RJ11(CA11A) type modular phone
jack, which is the most common type of phone jack
and might look like the one pictured here. If you
don’t have a modular jack, call your local phone
company to find out how to get one installed.
INSTALLATION NOTE: Some cordless telephones
operate at frequencies that may cause interference to
nearby TVs microwave ovens, and VCRs. To minimize
or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a
TV, microwave ovens, or VCR. If such interference
continues, move the cordless telephone farther away
from these appliances. Certain other communications
devices may also use the 2.4 GHz frequency for
communication, and, if properly set, these devices may
interfere with each other and/or your new telephone.
If you are concerned with interference, please refer to
the owner’s manual for these devices on how to
properly set channels to avoid interference. Typical
devices that may use the 2.4 GHz frequency for
communication include wireless audio/video senders,
wireless computer networks, multi-handset cordless
telephone systems, and some long-range cordless
telephone systems.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE OR
ELECTRICAL SHOCK HAZARD, DO
NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
THE LIGHTNING FLASH
AND ARROW HEAD
WITHIN THE TRIANGLE
IS A WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE THE
PRODUCT.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.
CAUTION:
Base
Handset
Mounting bracket
in use/VMWI
charge
PAGE
#
PAUSE
9
WXYZ
6
MNO
3
DEF
O
OPER
8
TUV
5
JKL
2
ABC
*
TONE
7
PQRS
4
GHI
1
chan
flash
r
e
d
i
a
l
c
a
n
c
e
l
TALK
FORMAT
CID
p
r
o
g
r
a
m
callback
hold
de
lete
mute
m
e
m
Belt clip
AC power
supply
Telephone
line cord
Handset battery
3
2
4
1
in use/VMWI
charge
PAGE
in use/VMWI
indicator
charge/PAGE
indicator
PAGE
button
Caller ID name
Time
Date
Number of calls
Caller ID phone number
#
PAUSE
9
WXYZ
6
MNO
3
DEF
O
OPER
8
TUV
5
JKL
2
ABC
*
TON E
7
PQRS
4
GHI
1
c
h
a
n
flash
r
e
d
ia
l
c
a
n
c
e
l
TALK
FORMAT
CID
p
r
o
g
r
a
m
c
a
l
l
b
a
c
k
hold
d
e
l
e
t
e
mute
m
e
m
2
1
4
5
7
6
3
#
PAUSE
9
WXYZ
6
MNO
3
DEF
O
OPER
8
TUV
5
JKL
2
AB C
*
TONE
7
PQRS
4
GHI
1
ch
a
n
fl
a
s
h
redial
cancel
TALK
FORMAT
CID
p
r
o
g
r
a
m
c
a
llb
a
c
k
hold
d
e
l
e
t
e
mute
m
e
m
VOLUME buttons
CID
review
button
chan
button
flash/
program
button
TALK/
callback
button
redial/
delete
button
TONE
button
mem
button
PAUSE
button
mute
button
RINGER
switch
cancel
button
hold
button
FORMAT
button
IMPORTANT INFORMATION
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements. The Industry Canada
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to
be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe systems, if present, are connected together. This precaution may be
particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or electrician,
as appropriate.
NOTES: This equipment may not be used on coin service provided by the
telephone company.
Party lines are subject to telephone company tariffs and, therefore, you may
not be able to use your own telephone equipment if you are on a party line.
Check with your local telephone company.
INTERFERENCE INFORMATION
This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly
installed and used in accordance with instructions contained in this manual.
Reasonable protection against such interference is ensured, although there is
no guarantee this will not occur in a given installation. If interference is
suspected and verified by switching this equipment on and off, the user is
encouraged to try to correct the interference by one or more of the following
measures: Reorient the radio/television receiver’s antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into
separate circuit outlets. The user may also wish to consult a qualified radio/
television technician for additional suggestions. This equipment has been
fully tested and complies with all limits for Class B computing devices
pursuant to part 15 FCC Rules and Regulations. This apparatus does not
exceed the class B limits for RF noise emissions specified in the RFI
regulations of the Industry Canada.
HEARING AID COMPATIBILITY
This telephone system meets FCC/Industry Canada standards for Hearing Aid
Compatibility.
ATLINKS Communications Canada Inc.
(An Alcatel /Thomson Multimedia Joint Venture)
© 2001 ATLINKS Communications Canada, Inc.
Trademark(s) ® Registered
Marque(s) ® déposée(s)