Bionaire BAP1250-U Air Cleaner User Manual


 
Read instructions before operating.
Retain for future reference.
Instruction Leaflet
INFO-LINE
If after having read this leaflet, you have any
questions or comments on your air cleaner,
call 1-800-253-2764 in North America.
AIR CLEANER SAFETY
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
•Read all instructions before using appliance.
•To avoid fire and shock hazard, plug the air cleaner and
EnviroCheck
TM
Wireless Air Quality Center directly into 120V
AC electrical outlets.
If the filter is covered by a bag when shipped: remove plastic
bag before use.
Keep the cords out of heavy traffic area. To avoid fire hazard
NEVER put cords under rugs, near heat registers, radiators,
stoves or heaters.
•To protect against electrical hazards DO NOT immerse in
water or other liquids. Do not use near water.
•Close supervision is necessary when any appliance is used by
or near children or disabled persons.
•Always unplug the air cleaner or EnviroCheck
TM
Wireless Air
Quality Center before moving it, opening the grill, changing
the filters, cleaning the IR Lens or whenever the appliances
are not in use. Be sure to pull by the plug and not the cord.
NEVER drop or insert any object into any openings.
Do not operate any appliance with a damaged cord or plug, if
motor fan fails to rotate, after the appliance malfunctions, or if it
has been dropped or damaged in any manner. Return appliance
to manufacturer for examination, electrical or mechanical
adjustment or repair.
•Use appliance only for the intended household use as
described in this manual. Any other use not recommended by
the manufacturer may cause fire, electrical shock or injury to
persons. The use of attachments not recommended or sold
by The Holmes Group may cause hazards.
Do not use outdoors.
Never block the air openings, or place on soft surface, such
as bed or sofa, as this could cause the unit to tip over thus
blocking the air intake opening.
EnviroCheck
TM
Wireless Air Quality Center should only be used
in a room with temperatures between 40° F and 110° F
Keep appliances away from heated surfaces and open flames.
DO NOT attempt to repair or adjust any electrical or
mechanical functions on these appliances. Doing so will void
the warranty. The inside of these appliances contain no user
serviceable parts. All servicing should be performed by
qualified personnel only.
WARNING: To reduce the risk of fire or electrical shock, DO
NOT use these appliances with any solid-state speed control
device.
DO NOT place anything on top of these appliances.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS PRODUCT IS EQUIPPED WITH A
POLARIZED PLUG (a plug having one
blade wider than the other). This plug
will fit into the power outlet only one
way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does
not fit, contact qualified personnel to
install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY.
The length of the cord used on this product was selected to
reduce the hazards of becoming tangled in, or tripping over a
longer cord. If a longer cord is necessary an approved extension
cord may be used. The electrical rating of the extension cord
must be equal to or greater than the rating of the air purifier. Care
must be taken to arrange the extension cord where it cannot be
pulled on by children or accidentally tripped over.
FEATURES
Dual Position – The air cleaner can stand upright or lie on its
side. Also designed to fit with its back flush against the wall.
When positioning the unit, please be sure the air inlet and air
outlets are not blocked to ensure maximum airflow.
Three Levels of Filtration:
Washable Foam Pre-Filter – Captures larger particles like pet
dander and prolongs the life of the HEPA and CARBON filters.
Carbon Filter – Helps reduce household odors and remove
larger particles.
HEPA Filter – Removes 99.97% of airborne particles as small as
0.3 microns from air passing through the filter. This includes things
like smoke, dust, pollen, ragweed, grass-
es, mold spores, dust mite debris and
pet dander.
Carbon Filter Indicator – When the
carbon filter indicator light turns red it is
time to change the carbon filters.
HEPA Filter Indicator – The filter life
monitor uses a series of lights to give
you an indication of the remaining filter
life. With new filters the bottom light will
be illuminated green. As the filter life progresses the filter life indi-
cator will move to yellow and your HEPA filters should be
checked for particulate accumulation. When the filter life indicator
light is red, it is time to change the HEPA filters.
EnviroCheck
TM
Wireless Air Quality
Center – Multifunctional providing an indoor air quality display,
auto mode, programmable controls, remote operation of air
cleaner as well as a clock and alarm mode.
Air Quality Sensor – Uses an advanced infrared optical system to
constantly detect tiny airborne particles in the air around the
EnviroCheck
TM
Wireless Air Quality Center, such as pollen and dust.
It displays the air quality conditions using a series of LED lights
glowing red when high levels of particles are present and green
when air quality is improved.
Advanced Communication Technology – Radio frequency
technology sends continuous signals between air cleaner and
EnviroCheck
TM
Wireless Air Quality Center.
Sensor Control Mode – When set to Sensor Control auto mode,
the sensor measures your indoor air quality and adjusts the fan speed
automatically to provide optimum filtration. It also helps conserve
energy by only operating the fan at higher speeds when needed.
Remote Operation – The function of the
EnviroCheck
TM
Wireless Air Qulaity Center
is similar to a remote control. From across
the room, you can operate your air cleaner
- you can change speed settings, turn off
the appliance or set to sensor control.
Programmable Controls – Gives you the
flexibility to program your air cleaner to turn
on and off at your convenience.
Clock/Alarm Mode – Convenient clock
and alarm mode make the EnviroCheck
TM
Wireless Air Quality
Center multi-functional. Replaces tabletop or nightstand clock.
Also features a 10 minute snooze alarm.
This product earned the ENERGY STAR by meeting strict energy
efficient guidelines set by the US EPA. The energy efficiency of the
ENERGY STAR qualified model is measured based on a ratio
between the model’s CADR for dust and the electrical energy it
consumes, or CADR/ Watt.
PRE-OPERATING INSTRUCTIONS
1. Carefully unpack your air cleaner. Select a firm level place
where there are no obstructions to the air inlet or filtered air
outlet. A good location in a room is approximately one foot
away from the wall, in a central location of your home.
2. Open the door of the air cleaner by carefully placing fingers in the
indentation on the right side of the door and gently pull forward.
3. The carbon filters, which are packed in a plastic bag in the
box, should be removed from plastic bag and then placed on
each of the HEPA filters. The plastic tabs on the HEPA filter
will hold the carbon in place. (Figure 1)
4. This model utilizes a hang tab. The filter
should easily slide onto the filter hang tab
with only a small amount of pressure.
(Figure 2)
NOTE: The side with the soft gasket
should face inward.
5. Replace the front grill by swinging door
closed and gently press until front grill is
firmly in place.
6. Carefully remove your EnviroCheck
TM
Wireless Air Quality Center from the
packaging materials.
7. Select a firm level place on a tabletop or
counter where there are no obstructions
to the venting holes.
SYNCRONIZING INSTRUCTIONS
1. Plug the air cleaner into a 120V AC electrical outlet. The air clean-
er will begin to beep continuously until it is synchronized with the
EnviroCheck
TM
Wireless Air Quality Center.
2. Plug the EnviroCheck
TM
Wireless Air Quality Center into a
120V AC electrical outlet near the air cleaner. It will beep
once. NOTE: EnviroCheck
TM
Wireless Air Quality Center is
designed to operate up to 30 feet from air cleaner.
on/off
mode
O
N
T
I
M
E
R
H
I
PM
SENSOR CONTROL
PM
timer
set
clock
alarm
3. Synchronize the appliances by simply pressing the on/off button
on the EnviroCheck
TM
Wireless Air Quality Center. The air cleaner
will beep in rapid succession for a few seconds. The
EnviroCheck
TM
Wireless Air Quality Center is now ready to
operate with your air cleaner.
PROGRAMMING INSTRUCTIONS
CLOCK
When the EnviroCheck
TM
Wireless Air Quality Center is plugged into
the electrical outlet, the time will automatically set for 12:00 am. After
the clock has been set it will show current time as long as the appli-
ance is plugged in.
1. To set the clock time, press the “CLOCK” and “SET” buttons
at the same time. The hour numbers will begin to flash.
2. Press “+” or “-“ to set desired hour., then press “SET”.
3. When a button has not been pressed for a few seconds OR
when the “SET” button is pressed again, the minute numbers
will begin to flash.
4. Press the “+” and “-“ buttons to adjust the minutes as indicat-
ed above in step 2.
5. When a button has not been pressed for a few seconds OR
when the “SET” button is pushed again the clock will begin
operating.
ALARM
The EnviroCheck
TM
Wireless Air Quality Center is equipped with
an alarm clock option.
Setting Alarm
1. To set the alarm, press the “ALARM” and
“SET” buttons at the same time. The hour
numbers will begin to flash and a small bell
will appear in the bottom right hand corner
of the LCD screen.
2. Press “+” or “-“ to set desired hour., then press “SET”.
3. When a button has not been pressed for a few seconds OR
when the “SET” button is pressed again, the minute numbers
will begin to flash.
4. Press the “+” and “-“ buttons to adjust the minutes as indicat-
ed above in step 2.
5. When a button has not been pressed for a few seconds OR
when the “SET” button is pushed again the time will appear
on the LCD screen and the alarm is set. A small bell will now
appear in the bottom right hand corner indicating the alarm is
operational.
6. To check the alarm setting, press the “ALARM” button. The
alarm set time will appear. Press the “TIME” button to return
to clock mode.
Turning Alarm OFF
1. When the alarm goes off, a rapid beeping will be heard.
2. To deactivate the alarm press the “ALARM” and “SET” buttons at
the same time. The bell in the right hand corner will disappear.
3. The longer the alarm sounds the louder it gets.
4. The alarm has a snooze feature. Press the “ALARM” button
when the alarm is sounding and the alarm will turn off. After 10
minutes, the alarm will sound again. The alarm will continue to go
off every 10 minutes until the alarm mode is deactivated. See
step 2 above.
Figure 1
Figure 2
d
e
ON TIMER
HI
PM
SENSOR CONTROL
PM
tim
e
r
s
e
t
c
lo
c
k
a
la
r
m
Programmable Timer
The EnviroCheck
TM
Wireless Air Quality Center has a programmable
timer feature. You can program the air cleaner to turn on and off at
your convenience. NOTE: The EnviroCheck
TM
Wireless Air Quality
Center must be used to turn the air cleaner on, set the operating
speed, and turn air cleaner off in order for the timer to work.
(Steps 1-3 below)
1. Using the EnviroCheck
TM
Wireless Air Quality Center turn the
air cleaner on by pressing the “ON/OFF” button. (See
Operating Instructions below for more details.)
2. Set the desired operating speed by using the “MODE” button.
3. Then using the EnviroCheck
TM
Wireless Air Quality Center turn
the air cleaner off by pressing the ”ON/OFF” button.
4. To program the timer press the “TIMER” and “SET” buttons
at the same time.
a) Set the “Timer On” time first: To set the time the air
cleaner will come on, press the “TIMER” and “SET”
buttons at the same time. The hour numbers in the
timer section will begin to flash.
b) Press “+” or “-“ to set desired hour., then press “SET”.
c) When a button has not been pressed for a few seconds
OR when the “SET” button is pressed again, the minute
numbers will begin to flash.
d) Press the “+” and “-“ buttons to adjust the minutes as
indicated above in step 2.
e) When a button has not been pressed for a few seconds
OR when the “SET” button is pushed again the timer
“ON” will be set and the Timer “OFF” will begin flashing.
f) Set the “Timer Off” time second by following instructions
in step 4a - e.
5. After completing timer set operation the “TIMER ON” and
programmed time will be displayed.
6. Once the unit has begun operating in timer mode the “TIMER
OFF” and programmed off-time will appear in the top display.
7. To turn off the programmable timer press and hold the
"TIMER" button for 3 seconds.
NOTE: If the air cleaner is turned on before timer mode begins,
the unit will remain on and “TIMER OFF” will appear on the
display. The air cleaner will still turn off as programmed.
EnviroCheck
TM
Wireless Air Quality Center
The EnviroCheck
TM
Wireless Air Quality Center serves as a command
center for the air cleaner. It remotely operates the air cleaner by
sending continuous signals from the EnviroCheck
TM
Wireless Air
Quality Center to the air cleaner. This one way communication
can be overridden by operating the controls directly on the air
cleaner. When using the EnviroCheck
TM
Wireless Air Quality
Center, the yellow LED on the air cleaner will illuminate. When
operating controls directly on the air cleaner, the Yellow LED light
will turn off. To resume primary control from the EnviroCheck
TM
Wireless Air Quality Center, press the ”ON/OFF” or “MODE” button.
The Yellow LED light on the air cleaner will again illuminate.
Operating Instructions
1. The air cleaner can be operated from either the control panel
directly on the air cleaner or the EnviroCheck
TM
Wireless Air
Quality Center.
2. To turn the air cleaner on, press the “ON/OFF” button on the
EnviroCheck
TM
Wireless Air Quality Center OR press the ( )
on the air cleaner.
3. Select the desired operating speed. This Bionaire
®
Air Cleaner
has four speed settings. You can select from <<HIGH>> ( ),
<<MED>> ( ), <<LOW>> ( ) or <<SLEEP>> ( ) by
pressing the “MODE” button on either the air cleaner control
panel or the EnviroCheck
TM
Wireless Air Quality Center.
4. The light on the control panel will illuminate letting you know the
power is on and at what speed the air cleaner is operating.
5. For optimum air filtration, it is recommended to operate the air
cleaner continuously. Its rugged motor has been designed to
provide many years of continuous use.
For continuous use, it is recommended to operate the air cleaner on
the LOW or MEDIUM setting. For quieter operation or use in a
bedroom, select the LOW or ultra-low SLEEP setting. When high
levels of air pollution are present, select the HIGH setting to quickly
circulate and filter the room air.
NIGHTLIGHT
Your EnviroCheck
TM
Wireless Air Quality Center has a built in
nightlight which automatically turns on as your room gets dark. To
turn off this nightlight press the "+" and "-" buttons at the same
time. To turn this function back on simply press both buttons
again. NOTE: When any button is pressed the backlight will
come on for a few seconds. Once no buttons are pressed again
for 5 seconds the light will go off.
Air Quality Sensor
Your Bionaire
®
Air Cleaner comes with an Air Quality Sensor which
uses an advanced infrared optical system to constantly detect tiny
particles in the air around the EnviroCheck
TM
Wireless Air Quality
Center such as pollen and dust. It also displays the air quality even
when the air cleaner is turned off, using a series of colored lights.
Radio frequency technology sends continuous signals between air
cleaner and the EnviroCheck
TM
Wireless Air Quality sensor and
adjusts air cleaner to improve air quality wherever it is placed.
The air quality sensor uses a series of lights to indicate air
quality conditions and particle levels. The lights range in color
from green which indicates good air quality conditions or low
levels of airborne particulate to red which shows poor air
quality conditions or high levels of airborne particulate.
The air quality sensor operates continuously when the
EnviroCheck
TM
Wireless Air Quality Center is plugged into a
120V AC outlet, even when the air cleaner is turned off.
Sensor Control Mode
When the EnviroCheck
TM
Wireless Air Quality Center is in the
“Sensor Control” mode, it will automatically adjust the fan setting
to the optimum speed based on the air quality conditions and
particle levels in the air. As the particle concentration in the air
rises, so does the speed. In sensor control mode, the unit will
always run at a minimum of SLEEP speed even if the particle
levels are low to maintain ideal conditions.
1. To turn the air cleaner onto “Sensor Control” mode you must
use the EnviroCheck
TM
Wireless Air Quality Center.
2. Turn the air cleaner on using the Operating Instructions.
Select the desired operating speed by scrolling through the
settings using the “MODE” button. You can select from “HI”,
“MED”, “LOW”, “SLEEP” or “Sensor Control”.
3. Once in “Sensor Control” mode, the air cleaner speed will
fluctuate depending on airborne particulate concentration.
NOTE: The Sensor Control mode can not be controlled from the
air cleaner control panel. It can only be controlled using the
EnviroCheck
TM
Wireless Air Quality Center.
CLEANING/MAINTENANCE INSTRUCTIONS
Air Cleaner Maintenance Instructions
Turn off and unplug the unit before cleaning.
1. The outside of the air cleaner can be cleaned with a soft,
damp cloth.
2. The filtered air outlet/top air vent can be cleaned of dust with
a small, soft brush.
3. You can remove the air inlet/front grill for cleaning by open the
door of the air cleaner. Carefully placing fingers in the indentation
on the right side of the door and gently pull forward. With
door open to 90 degrees pull grill up and forward. Once
removed front grill can be cleaned with warm soapy water. Do
not place in dishwasher. Make sure the grill is completely dry
before reinstalling. (Figure 3)
4. If you wish to clean the inside of the
air purifier, please remove filters and
only use a dry, soft cloth to wipe it
down.
5. DO NOT wash HEPA or CARBON
filters.
WARNING: Do not allow moisture to
come in contact with the main housing
of the air cleaner.
Pre-Filter Cleaning Instructions
1. Every 2-3 weeks check the conditions of the washable foam
pre-filter.
2. Open the front door and remove the pre-filter frame to exam-
ine the pre-filter. (see figure 3)
3. If the pre-filter has a noticeable amount of dust, lint or particu-
late accumulation, wash it by hand in warm soapy water. The
pre-filter must be washed at least every 30 days or more
often as necessary. If the pre-filter is worn or damaged
replace it. DO NOT wash in an automatic washer. Gently hand
wash only.
4. After washing, rinse and dry the pre-filter thoroughly before
replacing it into the air cleaner door. DO NOT dry the pre-filter
in an automatic dryer. Hand dry only by dabbing gently with a
hand dry cloth towel.
5. Replace pre-filter in door and latch pre-filter frame (see figure 4).
Filter Life Indicators
The HEPA Filter life indicator uses a
series of lights to give you an
indication of the remaining filter life. With
new filters, the lights on the air cleaner
display will be illuminated green. As filter
life progresses the filter life indicator will
move to yellow. When the filter light is
red, it is time to change the HEPA filters.
There is also a carbon filter indicator light
on the air cleaner control panel. When this light illuminates red, it
is time to change the Carbon filters.
FILTER REPLACEMENT INSTRUCTIONS
On average, HEPA filters need to be replaced every 12-18 months.
Carbon filters need to be replaced every 3-6 months. Filter life will
vary depending on air quality and usage.
1. Turn off and unplug your air cleaner before attempting to
replace the filters.
2. Remove each of the filters from the unit by pulling gently
towards you.
3. To replace the carbon filter, simply remove the old carbon filter
and using the plastic tabs as a guideline (see Figure 1), insert
a new carbon filter in its place after removing the plastic bag.
4. To replace the HEPA filter, discard the old HEPA filters. DO
NOT attempt to clean. Put the carbon filter back on the new
HEPA filter. Insert the new HEPA filter into the unit, by sliding it
on the hang tabs (see Figure 2).
5. After replacing the filters, RESET the appropriate Filter Life
Indicator by inserting a small object (such as a pin or paper
clip) into the hole below the filter change light. The series of
LED lights is the HEPA ( ) filter indicator and the red LED is
the carbon ( ) filter light.
NOTE: The side with the soft gasket should face
inward.Replacement filters are available from your local suppli-
er or by calling 1-800-253-2764.
Air Quality Sensor Cleaning Instructions
It is recommended that you clean the air quality sensor monthly to
maintain accurate monitoring or particulate levels.
1. The air quality sensor is located on the back
side of the EnviroCheck
TM
Wireless Air Quality
Center.
2. Open the sensor door (Figure 5)
3. Use a dry cotton swab to gently clean the
sensor lens. Do not use any water or cleaning
agents.
4. Securely close the sensor door. If it is not closed the sensor
may not operate properly.
STEP 1
STEP 2
Figure 3
Figure 4
TROUBLESHOOTING
SERVICE INSTRUCTIONS
1. Do NOT attempt to repair or adjust any electrical or mechani-
cal functions on this unit. Doing so will void the warranty. The
inside of the unit contains no user serviceable parts. All servic-
ing should be performed by qualified personnel only.
2. If you need to exchange the unit, please return it in its original
carton, with a sales receipt, to the store where you purchased
it. If you are returning the unit more than 30 days after the
date of purchase, please see the enclosed warranty.
3. Should your Air Cleaner require service, please call
1-800-253-2764 in North America for further assistance.
4. If you have any other questions or comments, feel free to
write to us:
Consumer Service Department
32B Spur Drive
El Paso, TX 79906
Visit our website at www.bionaire.com
Air Cleaner
Model #
BAP1225-CN
BAP1250-CN
Filter Quantity
Needed
2
2
3
3
Filter #
A1230H
A1260C
A1230H
A1260C
Filter
Description
HEPA
Carbon
HEPA
Carbon
Figure 5
TWO (2) YEARS FULL WARRANTY
Manufacturer warrants for TWO (2) YEARS from the date or
original purchase, to repair or, if repairs are not commercially
applicable to replace without charge (parts and labor), any
supplied or manufactured part of this air cleaner which, upon
inspection by an authorized service center, proves to have failed
in normal use due to defects in material or workmanship, or, at its
option, to replace the unit. If the product can not be reasonably
repaired, the consumer may elect a free replacement or refund.
Operations under conditions other than those recommended or
at voltages other than the voltage indicated on the unit, or any
attempts by unauthorized personnel to service the unit or modify
it, will render the guarantee void.
Manufacturer shall not be liable for any personal injury, property
damage or any incidental or consequential damages of any kind
(including water damage), resulting from defects, malfunctions,
misuse, improper installation or alteration of the product.
MANUFACTURER EXPRESSLY DISLAIMS ALL REPSONSIBILITY
FOR CONSEQUENTIAL DAMAGES OR INCIDENTAL LOSSES
FOR BREACH OF EXPRESS OR IMPLIED WARRANTIES
CAUSED BY USE OF THIS PRODUCT. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGE.
The provisions of this warranty are in addition to and not a
modification of or subtraction from the statutory warranties and
other rights and remedies contained in any applicable legislation
and to the extent that any such provision purports to disclaim,
exclude or limit any such statutory warranties or other rights or
remedies, such provisions shall be deemed to be amended to the
extent necessary to comply therewith.
For Warranty Service, please call 1-800-253-2764.
A Bionaire
®
customer service representative will help determine
which is the best procedure in order for your air cleaner to be
repaired.
KEEP THIS NUMBER FOR FUTURE REFERENCE
RADIO FREQUENCY COMPLIANCE INFORMATION
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interfer-
ence that may cause undesired operation of the device.
Modifications not authorized by the manufacturer may void
user 1st authority to operate this device.
Bionaire
®
, the Bionaire logo
®
and EnviroCheck
TM
are trademarks of The
Holmes Group, Inc. or its subsidiary.
Printed In China
Problem
Air Cleaner will
not operate
Decreased air flow
EnviroCheck
TM
Wireless Air Quality
Center is not
controlling unit
Air Quality Sensor
lights are always
green
Solution
Check to make sure air cleaner is
properly plugged in.
Check to make sure the air cleaner is
on by pressing the on/off or ( ) button.
Check the filters to see if they are in
good condition and if they need to be
changed.
Check to ensure nothing is blocking
air inlet and filtered air outlet.
Make sure the EnviroCheck
TM
Wireless
Air Quality Center is synchronized with
the air cleaner by following
synchronization instructions.
The Air Cleaner and EnviroCheck
TM
Wireless Air Quality Center can be re-
synchronized by holding down the
ON/OFF ( ) button on both the Air
Cleaner and the EnviroCheck
TM
Wireless Air Quality Center at the same
time for 5 seconds until you hear a rapid
beeping sound.
Chances are there are low levels of
airborne particles around the sensor.
This should not be a concern.
EnviroCheck
TM
99.97% HEPA
Air Cleaner
MODEL BAP1225-CN
BAP1250-CN
BAP1225/1250CN04EFM1.qxd 11/17/04 3:51 PM Page 1