Filter
Top Products
Speakerphone Caller ID
page 8
USER GUIDE
One-touch memory buttons*
PHONE BOOK
button*
Ringer volume control
Loudspeaker volume control
MENU buttons*
Microphone
SPEAKERPHONE
button — press this to
dial and speak with
the handset on hook.
REDIAL • PAUSE button — press
this to display the last number you
dialled. You may need
PAUSE function if your
phone is connected to a PBX.
this
button’s
SECRECY button
press this during a call to
prevent the caller from
hearing you. Press it
again when you
want to be heard
again.
Display
Loudspeaker
Installation
Fit a battery before you connect the phone to the telephone line.
You need a 9 V PP3/6FL22 battery (not supplied with the unit).
SAFETY WARNINGS
Before removing the
battery compartment cover,
always make sure the
telephone line cable is
unplugged at the socket
Do not install the unit
where it might get wet.
* While you are using these buttons for
system functions (storing numbers, etc.)
your phone line will be BUSY to callers.
Ignore any tones or recorded messages
from the exchange.
1
2
3
4
5
6
Remove the screw from the latch on the battery compart-
ment cover (on the underside of the unit). Squeeze the
latch to remove the cover
Take out the battery connection pad. Don’t pull on the
wires
Click the connectors on the battery firmly into the studs
on the pad
Place the battery in the compartment
Replace the cover and the screw, making sure it fits firmly
into place
Plug the telephone line cable into the socket
Conditions for use
You can connect your Speakerphone Caller ID to a public
exchange line in the UK; or to an extension on an approved PBX
using DTMF (tone) signalling and timed-break recall (TBR).
The ringer equivalence numbers (RENs) of all instruments
connected to an exchange line must not add up to more than 4.
The has a REN of 1; most other phones
and fax machines have a REN of 1 unless marked otherwise.
Speakerphone Caller ID
RECALL button
You will need this if your phone
is connected to a PBX, or if you
use BT’s Select Services.
If you need help, call the Binatone Help Line
9.00 am to 5.00 pm, Monday to Friday
0208 344 8870
Technical details
Temperature range Operating 0ºC to 40ºC
Storage -20ºC to 60ºC
Approvals ETS 300-001, CTR 38
PBX compatibility 100 ms timed break recall
Pause length: 3 seconds
Signalling type: DTMF (dual tone
multifrequency), also called tone dialling
The five numbers stored in the Redial memories can have up to
32 digits each.
.
Binatone Telecom plc operates a policy of continuous product improvement,
and so reserves the right to make changes to the product and functions
without notice
The Speakerphone Caller ID must be serviced by trained
engineers. NEVER attempt any repairs or adjustments yourself —
you could make the problem worse and invalidate the Guarantee.
Always make sure your Speakerphone Caller ID is fully plugged
into the telephone line socket.
Check that the ringer volume switch on the side of the unit is
not set to the lowest position.
Check that the total REN value of all equipment connected to
your telephone line is no more than 4. Disconnect one or
more telephones and see whether that helps.
Disconnect all other instruments connected to the same line
as the Speakerphone Caller ID and see whether you can make
a call.
Disconnect the Speakerphone Caller ID from the telephone
line and plug a different telephone into the socket. Try making
a call. If this works, the line is OK.
If you are using a two-way socket adapter, remove it and plug
a telephone directly into the socket. If the call now works, the
adapter may be faulty.
If you think the fault may be on the exchange line, contact
the service provider (the BT engineers on 151, or your cable
company).
If you still cannot identify the cause of the problem, contact
the Binatone Help Line.
Troubleshooting
If the phone does not ring …
If you cannot make calls …
Do not clean any part of
your Speakerphone Caller
ID with solvent chemicals,
abrasives or spray cleaners
which might get inside the
case and cause damage not
covered by the guarantee.
When necessary, clean it
with a damp cloth.
Keep your Speakerphone
Caller ID away from hot,
humid conditions or strong
sunlight.
Model 3488