Filter
Top Products
Quick start guide
AT&T SB67108
DECT 6.0 expansion handset
for use with AT&T model
SB67118
Plug the battery
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing up
as indicated.
Align the cover flat
against the battery
compartment, then
slide it upwards.
To lock the battery
compartment, turn
the latch clockwise
until it points to
the lock icon
as shown on the
graphic.
Step 1 Step 2
Step 3
Install and charge the handset battery
To charge the handset, place it in the
charger as shown. The CHARGE light
is on when the handset is charging.
Step 4
CHARGE
light
Add and register handsets
You can add up to nine additional SB67108
handsets (sold separately) to the SB67118, but
you must register each new handset with the
telephone base before use. Additional handsets
are assigned numbers in the order they are
registered (handsets 2 to 10).
To register a handset to your telephone base:
1. Make sure the handset is out of the charger
and the screen shows Press MENU on BS, sel
Registration & sel Register HS. Then put HS
in cradle before you begin registration.
2. On the telephone base, press MENU/ENTER.
3. Scroll down to Registration and press
MENU/ENTER.
4. Press MENU/ENTER again to select Register
HS.
Install and charge the handset battery
(continued)
See pages 5-7 in the AT&T SB67108 user’s manual for com-
plete battery installation instructions.
5. Place the unregistered handset into the
charger. The telephone base screen shows
Handset registering. It takes up to 60 seconds
to complete the registration. You hear a
beep when the registration is successful.
The handset shows Handset registered, and
then shows X: Handset X (X represents the
extension and handset number).
NOTE: If the registration is not successful, the screen shows
Press MENU on BS, sel Registration & sel Register HS.
Then put HS in cradle. To reset the handset, remove theset the handset, remove the
handset from the charger. Try the registration process again.
See pages 8-9 in the AT&T SB67108 user’s manual for
complete handset registration instructions.
Mailbox setup
Each handset has its own mailbox that is different
from the general mailbox on the base. If you turn
on the Auto attendant on the base, the caller can
leave a message on the handset mailbox after
two rings (Fast answer mode = On), or five rings
(Fast answer mode = Off).
To turn fast answer mode on or off:
Press theress the M.box softkey.
Press DIR or CID to scroll to Fast answer
mode. Press ENTER/MENU.
Press DIR or CID to select On or Off.
Press ENTER/MENU to save the setting and
return to the previous menu.
To record a new personal announcement:
Press the M.box softkey.
Press DIR or CID to scroll to Anncemnt
setup. Press ENTER/MENU to play current
announcement.
3. Press thePress the Change softkey, and then press the
Start softkey. The system announces, “Record
after the tone. Press Stop when you are done.”
4. Press the Stop softkey when finished. The
recorded announcement plays.
1.
2.
3.
4.
1.
2.
5. Press the OK softkey to use the new recorded
announcement.
-OR-
Press the Change softkey to re-record the
announcement.
See pages 20-24 in the AT&T SB67108 user’s manual for com-
plete handset mailbox instructions.
Message playback
You can play the messages for your handset
mailbox and the general mailbox. If you have new
messages, the system plays the new messages
(oldest first) automatically when you access the
mailbox.
To listen to new messages on a cordlesslisten to new messages on a cordless
handset:
When the handset is idle, press the M.box
softkey.
To listen to new messages on the general
mailbox:
When the handset is idle, press the M.box
softkey.
Press DIR or CID to scroll to General
mailbox.
Press ENTER/MENU.
1.
2.
3.
Add and register handsets (continued) Mailbox setup (continued)