ALCATEL Mobile Phones Temporis 23 Telephone User Manual


  Open as PDF
of 2
 
Model Temporis 23-RS
00030362 (Rev.1 R/E)
09-43
Printed in China
INTRODUCTION
Your Telephone is designed to give you flexibility in use, and high
quality performance. To get the most from your new telephone, we
suggest that you take a few minutes right now to read through this
instruction manual.
If you have any questions or problems, consult the Troubleshooting
Tips for the solution.
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the
most common type of phone jack and might look
like the one pictured here. If you don't have a mo-
dular jack, call your local phone company to find
out how to get one installed.
PARTS CHECKLIST
Your package should contain the following items:
FLASH BUTTON
Press the FLASH button instead of using the hook switch to activate
customer calling services such as call waiting or
call transfer, which are provided by your
local phone company.Select the appropriate
flash timing (on the bottom of the base,
600ms,300ms,100ms).
CARE AND MAINTENANCE
Avoid putting near heating appliances and devices that
generate electrical noise(for example, motors and fluores-
cent lamps).
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment of the unit.
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
Retain the original package in case you need to ship it at a
later date.
PROBLEM SOLUTION
TROUBLESHOOTING TIPS
Phone doesn't ring
Check hook switch to make sure it pops up.
Make sure TONE/PULSE is set to correct
position.
Base
Handset
INSTALLING THE PHONE
Your telephone should be placed on a level surface such as a
desk or table top, or you can mount it on a wall, A desktop/wall
mounting pedestal is built into the base of the phone.
WALL MOUNT INSTALLATION
Your telephone may also be mounted on a
wall plate (not included).
1. Plug the telephone line cord into
a modular wall phone jack.
2. Slip the mounting holes on the
base over the wall plate posts and
firmly slide the unit down into place.
To keep your phone working and looking good, follow these
guidelines:
Used equipment must be disposed of in compliance
with current environmental protection regulations.
You should return it to your reseller or dispose of it
in an approved recycling centre.
Make sure phone cord is securely
plugged in.
Make sure other phones aren't off the
hook at the same time you're using the
phone. It is normal for the volume to drop
when additional phones are used at the
same time.
RINGER VOLUME
You may control the ringer volume level with theswitch located
on the bottom of the base.
Can't be heard by
other party
Feedback when dialing
in PULSE mode
This is normal, Power fluctuates with
phone outpulsing.
You might have too many phones on
one line.
TONE button
1. Press the TONE button ( * ) after you
have connected to the service in order
to enable touch-tone dialing.
2. When you hang up, the phone auto-
matically returns to Pulse dialing mode.
T
EMPORARY
T
ONE
F
EATURE
If you have Pulse (rotary) service, and
want to access customer calling services
that require touch-tone dialing, such as
2. Slide the PULSE/TONE switch to TONE if you use Touch-Tone
1. Slide the RINGER volume (on the base) to the desired volume.
4. Plug the telephone line cord into a modular wall phone jack.
3. Plug the handset cord into the handset.
WRAPPING THE TELEPHONE LINE CORD
In desktop mode, you may want to wrap the excess
telephone line cord through the grooves provided on the
bottom of the base.
1. Lift the handset and wait for a dial tone.
2. Dial the telephone number you wish to call.
PLACING A PHONE CALL
TELEPHONE BASICS
RECEIVING A PHONE CALL
= ringer tone will be loud
= ringer tone will be low.
= ringer tone will be middle
Designer phone
User's Guide
1. When the phone rings, simply lift the handset and begin your
conversation.
No dial tone
Won't dial out
Flash
button
Redial
button
2. To end of conversation, return the handset to cradle.
Service; set it to PULSE if you have rotary service.
getting information from a local bank, you
can use this feature.
REDIAL BUTTON
This unit redials up to 32 digits. To
automatically redial the last number You called:
1. Pick up the handset to get a dial tone.
2. Press redial.
1
Thomson Telecom
46 quai Alphonse le Gallo
92100 Boulogne Billancourt
France
www.thomson-asia.com.hk
Alcatel logo and Alcatel name are trademarks of Alcatel and used under license
by Thomson Telecom.
Model ALCATEL Temporis 23
Certificate of conformity № РОСС FR.МЛ05.H01000 valid till September 6, 2012
Declaration of conformity № Д-Т-0981 valid till September 10, 2014
Life cycle 5 years
INFORMATION ON PRODUCT CERTIFICATION
4
2
1
3
2
Model Temporis 23-RS
00030362 (Rev.1 R/E)
09-43
Printed in China
INTRODUCTION
Your Telephone is designed to give you flexibility in use, and high
quality performance. To get the most from your new telephone, we
suggest that you take a few minutes right now to read through this
instruction manual.
If you have any questions or problems, consult the Troubleshooting
Tips for the solution.
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the
most common type of phone jack and might look
like the one pictured here. If you don't have a mo-
dular jack, call your local phone company to find
out how to get one installed.
PARTS CHECKLIST
Your package should contain the following items:
FLASH BUTTON
Press the FLASH button instead of using the hook switch to activate
customer calling services such as call waiting or
call transfer, which are provided by your
local phone company.Select the appropriate
flash timing (on the bottom of the base,
600ms,300ms,100ms).
CARE AND MAINTENANCE
Avoid putting near heating appliances and devices that
generate electrical noise(for example, motors and fluores-
cent lamps).
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment of the unit.
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
Retain the original package in case you need to ship it at a
later date.
PROBLEM SOLUTION
TROUBLESHOOTING TIPS
Phone doesn't ring
Check hook switch to make sure it pops up.
Make sure TONE/PULSE is set to correct
position.
Base
Handset
INSTALLING THE PHONE
Your telephone should be placed on a level surface such as a
desk or table top, or you can mount it on a wall, A desktop/wall
mounting pedestal is built into the base of the phone.
WALL MOUNT INSTALLATION
Your telephone may also be mounted on a
wall plate (not included).
1. Plug the telephone line cord into
a modular wall phone jack.
2. Slip the mounting holes on the
base over the wall plate posts and
firmly slide the unit down into place.
To keep your phone working and looking good, follow these
guidelines:
Used equipment must be disposed of in compliance
with current environmental protection regulations.
You should return it to your reseller or dispose of it
in an approved recycling centre.
Make sure phone cord is securely
plugged in.
Make sure other phones aren't off the
hook at the same time you're using the
phone. It is normal for the volume to drop
when additional phones are used at the
same time.
RINGER VOLUME
You may control the ringer volume level with theswitch located
on the bottom of the base.
Can't be heard by
other party
Feedback when dialing
in PULSE mode
This is normal, Power fluctuates with
phone outpulsing.
You might have too many phones on
one line.
TONE button
1. Press the TONE button ( * ) after you
have connected to the service in order
to enable touch-tone dialing.
2. When you hang up, the phone auto-
matically returns to Pulse dialing mode.
TEMPORARY TONE FEATURE
If you have Pulse (rotary) service, and
want to access customer calling services
that require touch-tone dialing, such as
2. Slide the PULSE/TONE switch to TONE if you use Touch-Tone
1. Slide the RINGER volume (on the base) to the desired volume.
4. Plug the telephone line cord into a modular wall phone jack.
3. Plug the handset cord into the handset.
WRAPPING THE TELEPHONE LINE CORD
In desktop mode, you may want to wrap the excess
telephone line cord through the grooves provided on the
bottom of the base.
1. Lift the handset and wait for a dial tone.
2. Dial the telephone number you wish to call.
PLACING A PHONE CALL
TELEPHONE BASICS
RECEIVING A PHONE CALL
= ringer tone will be loud
= ringer tone will be low.
= ringer tone will be middle
Designer phone
User's Guide
1. When the phone rings, simply lift the handset and begin your
conversation.
No dial tone
Won't dial out
Flash
button
Redial
button
2. To end of conversation, return the handset to cradle.
Service; set it to PULSE if you have rotary service.
getting information from a local bank, you
can use this feature.
REDIAL BUTTON
This unit redials up to 32 digits. To
automatically redial the last number You called:
1. Pick up the handset to get a dial tone.
2. Press redial.
1
Thomson Telecom
46 quai Alphonse le Gallo
92100 Boulogne Billancourt
France
www.thomson-asia.com.hk
Alcatel logo and Alcatel name are trademarks of Alcatel and used under license
by Thomson Telecom.
Model ALCATEL Temporis 23
Certificate of conformity № РОСС FR.МЛ05.H01000 valid till September 6, 2012
Declaration of conformity № Д-Т-0981 valid till September 10, 2014
Life cycle 5 years
INFORMATION ON PRODUCT CERTIFICATION
4
2
1
3
2
Model Temporis 23-RS
00030362 (Rev.1 R/E)
09-43
Printed in China
INTRODUCTION
Your Telephone is designed to give you flexibility in use, and high
quality performance. To get the most from your new telephone, we
suggest that you take a few minutes right now to read through this
instruction manual.
If you have any questions or problems, consult the Troubleshooting
Tips for the solution.
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the
most common type of phone jack and might look
like the one pictured here. If you don't have a mo-
dular jack, call your local phone company to find
out how to get one installed.
PARTS CHECKLIST
Your package should contain the following items:
FLASH BUTTON
Press the FLASH button instead of using the hook switch to activate
customer calling services such as call waiting or
call transfer, which are provided by your
local phone company.Select the appropriate
flash timing (on the bottom of the base,
600ms,300ms,100ms).
CARE AND MAINTENANCE
Avoid putting near heating appliances and devices that
generate electrical noise(for example, motors and fluores-
cent lamps).
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment of the unit.
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
Retain the original package in case you need to ship it at a
later date.
PROBLEM SOLUTION
TROUBLESHOOTING TIPS
Phone doesn't ring
Check hook switch to make sure it pops up.
Make sure TONE/PULSE is set to correct
position.
Base
Handset
INSTALLING THE PHONE
Your telephone should be placed on a level surface such as a
desk or table top, or you can mount it on a wall, A desktop/wall
mounting pedestal is built into the base of the phone.
WALL MOUNT INSTALLATION
Your telephone may also be mounted on a
wall plate (not included).
1. Plug the telephone line cord into
a modular wall phone jack.
2. Slip the mounting holes on the
base over the wall plate posts and
firmly slide the unit down into place.
To keep your phone working and looking good, follow these
guidelines:
Used equipment must be disposed of in compliance
with current environmental protection regulations.
You should return it to your reseller or dispose of it
in an approved recycling centre.
Make sure phone cord is securely
plugged in.
Make sure other phones aren't off the
hook at the same time you're using the
phone. It is normal for the volume to drop
when additional phones are used at the
same time.
RINGER VOLUME
You may control the ringer volume level with theswitch located
on the bottom of the base.
Can't be heard by
other party
Feedback when dialing
in PULSE mode
This is normal, Power fluctuates with
phone outpulsing.
You might have too many phones on
one line.
TONE button
1. Press the TONE button ( * ) after you
have connected to the service in order
to enable touch-tone dialing.
2. When you hang up, the phone auto-
matically returns to Pulse dialing mode.
TEMPORARY TONE FEATURE
If you have Pulse (rotary) service, and
want to access customer calling services
that require touch-tone dialing, such as
2. Slide the PULSE/TONE switch to TONE if you use Touch-Tone
1. Slide the RINGER volume (on the base) to the desired volume.
4. Plug the telephone line cord into a modular wall phone jack.
3. Plug the handset cord into the handset.
WRAPPING THE TELEPHONE LINE CORD
In desktop mode, you may want to wrap the excess
telephone line cord through the grooves provided on the
bottom of the base.
1. Lift the handset and wait for a dial tone.
2. Dial the telephone number you wish to call.
PLACING A PHONE CALL
TELEPHONE BASICS
RECEIVING A PHONE CALL
= ringer tone will be loud
= ringer tone will be low.
= ringer tone will be middle
Designer phone
User's Guide
1. When the phone rings, simply lift the handset and begin your
conversation.
No dial tone
Won't dial out
Flash
button
Redial
button
2. To end of conversation, return the handset to cradle.
Service; set it to PULSE if you have rotary service.
getting information from a local bank, you
can use this feature.
REDIAL BUTTON
This unit redials up to 32 digits. To
automatically redial the last number You called:
1. Pick up the handset to get a dial tone.
2. Press redial.
1
Thomson Telecom
46 quai Alphonse le Gallo
92100 Boulogne Billancourt
France
www.thomson-asia.com.hk
Alcatel logo and Alcatel name are trademarks of Alcatel and used under license
by Thomson Telecom.
Model ALCATEL Temporis 23
Certificate of conformity № РОСС FR.МЛ05.H01000 valid till September 6, 2012
Declaration of conformity № Д-Т-0981 valid till September 10, 2014
Life cycle 5 years
INFORMATION ON PRODUCT CERTIFICATION
4
2
1
3
2
Model Temporis 23-RS
00030362 (Rev.1 R/E)
09-43
Printed in China
INTRODUCTION
Your Telephone is designed to give you flexibility in use, and high
quality performance. To get the most from your new telephone, we
suggest that you take a few minutes right now to read through this
instruction manual.
If you have any questions or problems, consult the Troubleshooting
Tips for the solution.
BEFORE YOU BEGIN
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the
most common type of phone jack and might look
like the one pictured here. If you don't have a mo-
dular jack, call your local phone company to find
out how to get one installed.
PARTS CHECKLIST
Your package should contain the following items:
FLASH BUTTON
Press the FLASH button instead of using the hook switch to activate
customer calling services such as call waiting or
call transfer, which are provided by your
local phone company.Select the appropriate
flash timing (on the bottom of the base,
600ms,300ms,100ms).
CARE AND MAINTENANCE
Avoid putting near heating appliances and devices that
generate electrical noise(for example, motors and fluores-
cent lamps).
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment of the unit.
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
Retain the original package in case you need to ship it at a
later date.
PROBLEM SOLUTION
TROUBLESHOOTING TIPS
Phone doesn't ring
Check hook switch to make sure it pops up.
Make sure TONE/PULSE is set to correct
position.
Base
Handset
INSTALLING THE PHONE
Your telephone should be placed on a level surface such as a
desk or table top, or you can mount it on a wall, A desktop/wall
mounting pedestal is built into the base of the phone.
WALL MOUNT INSTALLATION
Your telephone may also be mounted on a
wall plate (not included).
1. Plug the telephone line cord into
a modular wall phone jack.
2. Slip the mounting holes on the
base over the wall plate posts and
firmly slide the unit down into place.
To keep your phone working and looking good, follow these
guidelines:
Used equipment must be disposed of in compliance
with current environmental protection regulations.
You should return it to your reseller or dispose of it
in an approved recycling centre.
Make sure phone cord is securely
plugged in.
Make sure other phones aren't off the
hook at the same time you're using the
phone. It is normal for the volume to drop
when additional phones are used at the
same time.
RINGER VOLUME
You may control the ringer volume level with theswitch located
on the bottom of the base.
Can't be heard by
other party
Feedback when dialing
in PULSE mode
This is normal, Power fluctuates with
phone outpulsing.
You might have too many phones on
one line.
TONE button
1. Press the TONE button ( * ) after you
have connected to the service in order
to enable touch-tone dialing.
2. When you hang up, the phone auto-
matically returns to Pulse dialing mode.
TEMPORARY TONE FEATURE
If you have Pulse (rotary) service, and
want to access customer calling services
that require touch-tone dialing, such as
2. Slide the PULSE/TONE switch to TONE if you use Touch-Tone
1. Slide the RINGER volume (on the base) to the desired volume.
4. Plug the telephone line cord into a modular wall phone jack.
3. Plug the handset cord into the handset.
WRAPPING THE TELEPHONE LINE CORD
In desktop mode, you may want to wrap the excess
telephone line cord through the grooves provided on the
bottom of the base.
1. Lift the handset and wait for a dial tone.
2. Dial the telephone number you wish to call.
PLACING A PHONE CALL
TELEPHONE BASICS
RECEIVING A PHONE CALL
= ringer tone will be loud
= ringer tone will be low.
= ringer tone will be middle
Designer phone
User's Guide
1. When the phone rings, simply lift the handset and begin your
conversation.
No dial tone
Won't dial out
Flash
button
Redial
button
2. To end of conversation, return the handset to cradle.
Service; set it to PULSE if you have rotary service.
getting information from a local bank, you
can use this feature.
REDIAL BUTTON
This unit redials up to 32 digits. To
automatically redial the last number You called:
1. Pick up the handset to get a dial tone.
2. Press redial.
1
Thomson Telecom
46 quai Alphonse le Gallo
92100 Boulogne Billancourt
France
www.thomson-asia.com.hk
Alcatel logo and Alcatel name are trademarks of Alcatel and used under license
by Thomson Telecom.
Model ALCATEL Temporis 23
Certificate of conformity № РОСС FR.МЛ05.H01000 valid till September 6, 2012
Declaration of conformity № Д-Т-0981 valid till September 10, 2014
Life cycle 5 years
INFORMATION ON PRODUCT CERTIFICATION
4
2
1
3
2
Model Temporis 23-SA
10000002 Rev.1 (E)
10-09
Printed in China
Product imported by :
Commsolve (Pty) Ltd
info@stingray.co.za
Tel : + 27 21 442 1540
Fax: + 27 21 448 8033
ATLINKS
22 quai Gallieni
92150 Suresnes
France
www.atlinks.com
Alcatel logo and Alcatel name are trademarks of Alcatel and used under license by ATLINKS.
User’s Guide